WMF 1300 S User Manual Download Page 84 | Manualshive

Page: 84 / 136

background image

84

User Manual WMF 1300 S

Software | Eco mode

5.12 Eco mode

If Eco mode is set to active, the steam boiler
temperature is reduced 10 minutes after the last
beverage is dispensed.
The beverage buttons remain lit.
If a beverage with a milk component is to be dispensed
when the temperature is reduced, the coffee machine
needs approx. 15 seconds to heat up.
Beverage dispensing starts after the machine has
heated up.

Eco mode

Options:

• On

• Off

• Timer

Default value:

inactive

The Eco mode can be activated here.

Eco mode display

The Eco mode symbol is displayed on the in the header
bar of the “Ready to operate” display.
There are two states.

Eco mode “active”

The coffee machine is currently in the reduce phase.

Eco mode “ready”

Eco mode is based on idle time, 10 minutes after the
latest beverage has been dispensed.

DI_eco

Eco mode

w

page 78

DI_eco

«
...
82
83
84
85
86
...
»

Summary of Contents for 1300 S









































































































































Reviews:

No comments

Related manuals for 1300 S

Brand: Saeco Pages: 20

PICOBARISTO HD8924

Brand: Saeco Pages: 30

Brand: Saeco Pages: 44

Brand: Saeco Pages: 80

Brand: Saeco Pages: 76

Brand: Saeco Pages: 26

Brand: Saeco Pages: 4

GranBaristoAvanti HD8967

Brand: Saeco Pages: 116

Brand: Saeco Pages: 22

Brand: Guzzanti Pages: 65

Brand: OK. Pages: 63

Triple Scoop KP300

Brand: Euro-Pro Pages: 16

Brand: U-Line Pages: 44

Brand: Faema Pages: 28

Brand: Gaggia Milano Pages: 159

Brand: Brady Pages: 201

GS-3405T Series

Brand: Gainscha Pages: 35

Brand: Malongo Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands