Witter ZX404 Assembly And User Instructions Manual Download Page 4

7.

! Attach packer plate if using bottom 

  holes.

! Do not attach packer plate if using 

  top holes.

page

 

13

page

 

4

To gain sufficient clearance

to open the tail-gate whilst

the carrier is tilted, lower the

carrier by using the upper

holes in the base plate.

Secure wheels into the wheel locators by feeding the strap into the buckle

and pulling down until tight. Note: To release the strap push in the strap 

retainer lever on the buckle.

How to operate ratchet straps and ratchet cycle arm clamps:

IMPORTANT: 

Ensure the strap is routed 

through the side aperture 

into the ratchet buckle.

                               

Continue to pump lever until the strap is tight against the cycle tube.

How to 

Tension

 cycle clamp arms with ratchet levers:

Push strap into

ratchet buckle.

Lift lever

Do not force lever !

On smaller diameter frames, take care that 

the rubber protector does not interfere with 

the operation of the ratchet system. 

It maybe necessary to trim the rubber 

to suit your frame size in this case.

Trim this area to

reduce length.

Do not over tighten !

Summary of Contents for ZX404









Reviews: