Witter ZX404 Assembly And User Instructions Manual Download Page 3

2.

1.

Remove and discard the M16 bolts, 

washers and nuts.

Note: Always use new M16 bolts, 

            washers and nuts.

page

 

3

Check towbar nose weight limit ( S - Vertical Static Mass ) -

Never exceed this limit, the sum of the carrier and bikes must be 

less weight than 

this limit.

? KG

Vehicle Handbook

page

 

14

M5 x 40

x 3

M16 x 60

x 2

To tilt the bike rack first support with your hands while you push the release 

handle with your foot. 

To avoid injury or damage, this operation of tilting the bike rack should be carried 

out 

with assistance

To close the bike rack lift until the release handle and mechanism click and engage 

securely in the transit position.

The Tilt mechanism indicator 

must

 show 

Green

 before you commence 

your journey.

transit position

release position

CARE MUST BE TAKEN WHEN TILTING THE CARRIER - WATCH YOUR HEAD AND FINGERS!

How to 

release

 cycle clamp arms with ratchet levers:

First push the release lever outwards, then pull out the strap.

Red                                           Tilt mechanism                                           Green

                                                        indicator

Summary of Contents for ZX404









Reviews: