Wittco 500-CW Installation & Operation Manual Download Page 8

500 & 700 CHIP WARMER 

 

F-41160 (09-12) 

 

 

OPERATION INSTRUCTIONS 

 

 

The Warmer and its 

parts are hot.  Be very careful when 
operating, cleaning, or servicing the 
warmer. 

 
1. 

Switch Power Switch to ON 

 

position.  Verify that switch 

 

illuminates. 

2. 

Open Top Door. 

3. 

Pour chips into Baffle. 

 

 Do not overfill.  The Top Door must 
be able to fully close. 
 

VCD5  holds approx. 22 gallons, and 
VCD44 holds approx. 44 gallons of 
chips. 

 

4. 

Close Top Door. 

5. 

After approx. 30 to 40 minutes, 

 

open Front Door to access 

 

warmed chips. 

6. 

Use the Chip Scoop to remove 

 

desired amount of chips. 

7. 

Close Front Door. 

 
 
 
 
 
 
 
 
 

SHUTDOWN 

 

 

The Warmer and its 

parts are hot.  Be very careful when 
operating, cleaning, or servicing the 
warmer. 

 
At the end of the day, switch Power 
Switch to OFF position.  Follow cleaning 
instructions in this manual, if necessary. 
 

EXTENDED SHUTDOWN 

 

 

The Warmer and its 

parts are hot.  Be very careful when 
operating, cleaning, or servicing the 
warmer. 

 
Perform the following procedure to shut 
down the Chip Warmer for an extended 
shutdown. 
 
1. 

Switch Power Switch to OFF 

 

position. 

2.  

Unplug Chip Warmer. 

3. 

Wait until Warmer cools down. 

4. 

Thoroughly clean Warmer.  Refer 

 

to “General Cleaning” instructions 

 

in the MAINTENANCE section of 

 

this manual. 

5. 

Leave all doors slightly open to 

 

allow for ventilation. 

 
 

SPECIFICATIONS 

MODEL

HEIGHT

DEPTH

WIDTH

SHIPPING 

WEIGHT

VOLTS WATTS

AMPS.

500-CW

20.75 "         

527 mm

27.75 "      

705 mm

24.25 "         

616 mm

115 #       

52 kg.

120

1250

10.5

700-CW

38.5 "       

978 mm   

27.75 "      

705 mm

24.25 "       

616 mm

160 #             

73 kg.

120

1250

10.5

 

Summary of Contents for 500-CW














Reviews: