background image

Wishbone Jumbo / Wheelchair Outhouse Assembly Guide

PARTS LIST 

Hardware 

Wall Lumber  Jumbo  Wheelchair 

SP0607 

¼

” x 

¾

” Button Head Bolt (12/16) 

Side Wall (52) 

31 

9

/

16

” 

37 

½

” 

SP0610 

¼

” x 1 

¼

” Button Head Bolt (8/16) 

Back Wall (26) 

31 

9

/

16

” 

31 

9

/

16

” 

SP0809 

” x 1” Button Head Bolt (16/16) 

Front Wall (26) 

12 

½

” 

12 

½

” 

SJ0614 

¼

” x 2 

¼

” Carriage Bolt (4/4)  

Door (12) 

31 

9

/

16

” 

31 

9

/

16

” 

SU0611 

¼

” x 1

½

” Hex Cap Bolt (1/1) 

SA0605 

¼

” Hex Nut (15/19) 

SB0505 

¼

” Flat Washer (4/8) 

SJ0610 

¼

” x 1 

¼

” Carriage Bolt (10/10) 

 

½

” x 6 

” ID U-Bolt (1/1) 

2

 

The John 

Roof

2” x 

¼

” 

Flat Bar

Left Side Boards 

Jumbo: 31 

9

/

16

” (26) 

WC :    37 

½

” (26)

Back Side Boards 

31 

9

/

16

” (26)

Right Side Boards 

Jumbo: 31 

9

/

16

” (26) 

WC :    37 

½

” (26)

2” x 

¼

” 

Flat Bar

Front Side Boards 

12 

½

” (26)

Corner Feet (4)

Front Door Boards 

31 

9

/

16

” (12)

The Forest 

Roof

Required Tools 

5

/

32

” Allen Key 

¼

” Nut Driver 

7

/

32

” Allen Key 

17

 

/

64

” Drill 

10” Crescent Wrench 

2 Small Step Ladders 

7

/

16

” Wrench or Socket 

 

Note:  Extra hardware included for different outhouse configurations/options. 

 

Above list shows hardware (required/included). 

 

Extra lumber included for repairs. 

Summary of Contents for FOREST FSTB-1



















Reviews: