background image

 

11 

 

USING THE CORRECT FUEL  

ALL PELLET FUELS ARE NOT CREATED EQUAL!  

WiseWay Pellet Stoves does not recommend buying pellet fuel in bulk until experience has 
revealed the best pellet fuel available in your area. 

 

 

The WiseWay stove was developed to burn pelletized wood fuel only! Pellets ¼” in 
diameter and approximately 1” long should be used. 
 

 

Burning fuels other than wood pelletized fuel is not permitted. 

 

 

This stove feeds pellets at a preset rate. Adding fuel by hand or burning fuel other than 
pellets will not increase the heat output but could impair the stove performance. 

 

 

DO NOT

 try to burn wet pellets or pellets that were previously opened and have been 

stored in the elements. Pellets that are stored in the elements are prone to absorbing 
moisture resulting in poor performance from the stove. Storing opened pellets indoors 
or in an air tight container is recommended. 

 

 

Stove performance not only depends on the quality of the pipe installation but also on 
the quality of the pellet fuel introduced to the stove. Avoid the use of pellets with 
excess fines, binders or high ash content. ONLY USE PREMIUM GRADE PELLETS WITH AN 
ASH CONTENT OF .5% OR LESS. 

 

 

DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA, 
ENGINE OIL OR ANY OTHER SUBSTITUTE MATERIALS. 

 

 

HOT SURFACES WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE 
AWAY. CONTACT MAY CAUSE SKIN BURNS. 
 

 

STORE PELLETS IN A DRY AREA. DO NOT STORE PELLET FUEL WITHIN THE STOVE 
INSTALLATION CLEARANCES OR WITHIN THE SPACE REQUIRED FOR CHARGING AND 
ASH REMOVAL. 

 

Summary of Contents for GW-1949-W





















Reviews: