I. Product Overview
1.Camera Lens
2.Indicator Light
3.Power Button
4.Mode Switch
5.Microphone
6.USB Port
7.Micro SD Card Slot
8.USB Mode Switch
9.Cover
II. What’s in the Box
1. Bike Handlebar Mount
2. Buckle Clip Mount
3. Curved Mount Adhesive Pads
4. AC110-230V to DC 5V Charging Adapter
5. Rubber Seals
6. Scope Mount Ring
7. Backup Waterproof Cover
8. Flat Mount Adhesive Pads
9. Cleaning Cloth
10. Waterproof Action Camera
11. Lanyard
12. USB Cable
13. Helmet Strap Mount
III. Mounting Instruction
3.1. HELMET STRAP MOUNT
3.1.1. Buckle up the Scope Mount Ring around the sports camera.
3.1.2. Push the Buckle Clip Mount into the Helmet Strap Mount.
3.1.3. Screw the Scope Mount Ring onto the Buckle Clip Mount and attach the
strap to your bike helmet.
3.2. BIKE CAMERA MOUNT
3.2.1. Buckle up the Scope Mount Ring around the sports camera (See 3.1.1).
3.2.2. Push the Buckle Clip Mount into the Bike Handlebar Mount.
3.2.3. Screw the Scope Mount Ring onto the Buckle Clip Mount, unscrew the
bolt on the Bike Handlebar Mount, then install the whole device on your bike
handlebar and screw the bolt back.
3.3. SURFBOARD CAMERA MOUNT
3.3.1. Buckle up the Scope Mount Ring around the sports camera (See 3.1.1).
3.3.2. Remove one release liner of the double-side adhesive tape and stick the
tape on the flat mount pad. Push the Buckle Clip Mount into the flat mount
adhesive pad.
3.3.3. Screw the Scope Mount Ring onto the Buckle Clip Mount, remove the
other release liner of the double-side adhesive tape and stick the whole device
on a surfboard.
3.4. MOTORCYCLE HELMET CAMERA MOUNT
3.4.1. Buckle up the Scope Mount Ring around the sports camera. (See 3.1.1)
3.4.2. Remove one release liner of the double-side adhesive tape and stick the
tape on the curved mount pad. Push the Buckle Clip Mount into the curved
mount adhesive pad.
3.4.3. Screw the Scope Mount Ring onto the Buckle Clip Mount, take off the
other release liner of the double-side adhesive tape and stick the whole device
on a motorcycle helmet.
IV. Camera Operation
>> Please make sure your camera battery is fully recharged before using.
>> Please make sure the Micro SD card (4GB-32GB) has been formatted
already and is securely fitted into the camera’s SD card slot, or the camera will
not work. A SDHC Class 10 Micro SD card is recommended. If no Micro SD card
is fitted into the camera, the indicator light will turn blue and be off in 2 seconds,
then it will flash red 8 times and turn off again, the camera will shut down
automatically.
[Note]:
The camera will shut down automatically if it is in standby mode without any
operation more than 2 minutes.
4.1. VIDEO RECORDING
4.1.1. Slide the Mode Switch to the video recording position .
4.1.2. Power on the camera by pressing the Power Button for 2 seconds. The
camera will vibrate once; the indicator light will flash blue once and then be solid
blue, indicating the camera has entered into standby mode.
4.1.3. Press the Power Button once to record video. The indicator light will keep
flashing blue.
4.1.4. Press the Power Button once again to stop recording video. The camera
will vibrate once and the indicator light will be solid blue, indicating the camera is
back to standby mode.
4.1.5. Power off the camera by pressing the Power Button for 2 seconds again.
The camera will vibrate once, the indicator light will flash blue once and then turn
off.
[Note]:
1). A video file will be generated and saved every 3-6 minutes automatically.
2). The camera can record videos continuously for 3.5 hours on a full charge.
3). Video Format: AVI Video Resolution: 1920x1080P
4). Loop recording is supported.
4.2. CAMERA/STILL PHOTOGRAPHY
4.2.1. Slide the Mode Switch to the camera position .
4.2.2. Power on the camera by pressing the Power Button for 2 seconds. The
camera will vibrate once; the indicator light will flash blue once and be solid red,
indicating the camera has entered into standby mode.
4.2.3. Press the Power Button once. The camera will take a picture every 3
seconds automatically and the indicator light will flash red once every 3 seconds.
4.2.4. Press the Power Button once again to stop taking photos continuously.
The camera will vibrate once and the indicator light will be solid red, indicating
the camera is back to standby mode.
4.2.5. Power off the camera by pressing the Power Button for 2 seconds again.
The camera will vibrate once, the indicator light will turn blue and then turn off.
[Note]:
Picture Format: JPG Picture Resolution: 3264x2448
4.3. RECORDING AND CHARGING SIMULTANEOUSLY
4.3.1. Slide the Mode Switch to the video recording position and slide the
USB Mode Switch to the charging and recording position .
4.3.2. Connect the camera to a power bank or an outlet power supply by using
the USB cable and charging adapter provided.
4.3.3. The camera will be powered on and then start recording automatically.
The camera will vibrate once, the blue indicator light will flash once and then
keep flashing.
4.3.4. Press the Power Button once to stop recording video. The camera will
vibrate once and the indicator light will be solid blue, indicating the camera is
back to standby mode.
V. Video/Image Files Uploads
5.1. Option One: Using a Card Reader
5.1.1. Power off the camera, remove the Micro SD card and insert it into a card
reader.
5.1.2. Insert the card reader into a proper PC computer USB port.
5.1.3. The card reader will be recognized as a removable disk drive.
5.1.4. All the files can be accessed in the drive.
5.2. Option Two: Using the USB cable
5.2.1. Power off the camera and slide the USB mode switch to the data transfer
position .
5.2.2. Connect the camera to a proper PC computer USB port by using the USB
cable provided. The indicator light will flash blue once and then keep flashing
red.
5.2.3. The camera will be recognized as a removable disk drive.
5.2.4. All the files can be accessed in the drive.
VI. Setting Time/Date Stamp and Video Length
6.1. Power off the camera, remove the Micro SD card and insert it into a card
reader.
6.2. Insert the card reader into a proper PC computer USB port.
6.3. Removable disk drive folder appears.
6.4. Click on the drive in the root directory and inside the root directory, create a
file named “time.txt”.
6.5. Write the current date, time and desired video length in the “time.txt” file with
the correct format: for example: 2016.04.12 14:24:32 Y 3.
"Y" means the time stamp on the video is enabled; "3" means each video length
will be 3 minutes.
If you don’t need the time stamp, change "Y" into "N" in the “time.txt” file (For
example: 2016.04.12 14:24:32 N 3).
If you want to extend video clip's duration time, change 3 into 4, 5 or 6 in the
“time.txt” file. (For example: 2016.04.12 14:24:32 N 6).
6.6. Save this file and restart the camera. The system will upgrade the program
automatically.
VII. Charging Only
7.1. Remove the Micro SD card from the camera.
7.2. Connect the camera to an outlet AC power supply by using the USB cable
and the DC5V charging adapter provided.
7.3. The indicator light will keep flashing red during the charging process.
7.4. It will take 2.5 hours to obtain a full charge.
7.5. The indicator light will be solid red when the camera is fully recharged.
