Wiseup DVR-0031-4, User Manual

Page: 3 / 113

I. Product Overview
1. Camera Lens
2. Reset Button
3. Power Button
4. Power Input
5. Red Indicator Light
6. Blue Indicator Light
II. What’s in the Box
-1× WIFI Smoke Detector Camera
-1× AC110-240V to DC5V Power Adapter
III. Before You Start
3.1. Please make sure your camera is fully recharged before using.
3.2. If you want the camera to work 7/24 hours, please connect it to an AC outlet using the
DC5V power adapter provided.
3.3. For Android, iPhone and iPad users, please scan the QR code to download the
“
BVCAM ” APP.
IV. Network Setup
4.1. LAN (P2P) Mode Setup
4.1.1. Power on the camera by pressing the Power Button for about 2 seconds. It will take
up 1 minute for the WIFI signal to appear. When the blue indicator light starts flashing and
the red indicator light remains solid, it means the camera’s WIFI signal is ready.
4.1.2. Go to the WIFI or WLAN Setting page on your phone or mobile device, connect to
the camera’s WIFI signal named “
CM***** ”. Wait for the WIFI to be connected and your
phone status bar will appear WIFI symbol as below:
[Note]:
If the camera’s WIFI signal cannot be found after a long time, please recharge the camera
or reset it (See VIII).
4.1.3. Run the “ BVCAM ” APP.
4.1.4. Add the camera to the “ BVCAM ” APP as below:
For Android: Tap +> Tap Add the new online Device> Search for the camera > Tap the
camera icon > Tap OK or √.
For IOS: Tap +> Tap Add new online Camera> Search for the camera > Tap the camera
icon > Tap OK.
4.1.5. If the camera shows “ Online ” on the “ Live video ” page, it means the camera’s P2P
(LAN) setup is successful. You can check or record video in the P2P (LAN) mode.
[Note]:
1). If the camera shows “
Offline
”, this is normal. Exit the APP and open it again. Wait a minute and
the camera will be “ online ”.
2). In this P2P (LAN) mode, you can only view video locally, within 15 meters (49 feet) open range.
4.1.6. On the live video screen, you can gently put your index finger and thumb on the
screen then slide in and outward directions on a specific area to zoom in and out.
4.2. Remote View Setup (WAN Mode)
>> Before remote view setup, please make sure that the camera is successfully added to
the APP and it's online in the P2P (LAN) mode.
4.2.1. Launch the “ BVCAM ” APP.
4.2.2. Set up remote view function as below:
Step 1: Tap the setting icon on the “
Live video ” page then choose " Advance Config " or
“
Device Settings
”.
Step 2: Go to “ WIFI Config ” page and select a desired WIFI hotspot to enroll the camera in.
Step 3: Tap “ OK ” to complete the remote view setup and the camera will reboot automatically.
How to check if remote view function works?
1. Exit the “ BVCAM ” APP.
2. Back to the WIFI or WLAN setting page on your phone or mobile device, exit your phone
or mobile device from the current WIFI network, enroll your phone or mobile device in
another WIFI hotspot, or you can turn off the WIFI or WLAN function, enable your mobile
network data instead.
3. Launch the “ BVCAM ” APP again. If the camera shows “ Online ” on the “ Live video ” page,
it means the remote view setup is successful and the camera has entered into WAN mode.
Both blue and red indicator lights will be illuminated. You can go ahead to view live video or
record video remotely.
[Note]:
If the camera shows “ Device Offline ”, it means the remote view setup failed and you need to
reset the camera (See VIII) and set up all over again.
V. Motion Detection Recording Setup
>> Please make sure that the camera is added to the APP in LAN or WAN mode and it’s
online before you start.
5.1. Launch the “
BVCAM
” APP.
5.2. Set up motion detection photograph as below:
Step1: Tap the setting icon on the “
Live video ” page then choose " Advance Config " or
“ Device Settings ”.
Step 2: Go to “ Alarm Config ” page, there, you can set a desired alarm sensitivity level, alarm
schedule, and alarm interval time. Enabling the “
Warning Tone
”, “
Push Notification
” and
“ On-screen Display ” is also available.
Step 3: Tap “ OK ” to complete the setting.
Step 4: When motion is detected, the camera will push a warning message to your phone and
will take a screenshot of the live video page automatically. You can go back to the “
Live video ”
page and tap “
Alarm
” at the bottom of the screen to check out the photos.
5.3. Set up SD card video recording based on motion detection as below:
Step 1: Tap the setting icon on the “
Live video ” page then choose " Advance Config " or
“
Device Settings
”.
Step 2: Go to “ SDCard Record Config ” page and choose “ On alarm ”, then set resolution and
file length. Enabling “ Record sound ” and “ Loop recording ” is also available.
Step 3: Tap “ OK ” to complete the Motion Detection Video Recording setting.
Step 4: When motion is detected, the camera will push an alarm message to your phone or
mobile device and record a video to the internal memory of the camera automatically. You can
go back to the “
Live video ” page, tap “ Record ” at the bottom of the screen and then tap
" Remote SD Card " or to check out the video files.
[Note]:
1). Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
2). If for any reason, the video files cannot be saved in the internal memory, you can format the
memory by tapping “
Format
”.
VI. Recording Video to Smartphone or Tablet PC
>> Please make sure that the camera is added to the APP in LAN or WAN before you start.
6.1. Launch the “ BVCAM ” APP. Tap the camera icon to get into the live video screen.
6.2. Tap the video recording button and audio button to start or stop recording
video.
For Android users, the video files will be saved in your mobile device's flash memory. For
IOS users, the video files will be only saved in the APP “
BVCAM ”. 6.3. Go back to the “ Live video ” page, tap “ Record ” at the bottom of the screen and then
tap " Loca l" or to check out the video files.
[Note]:
Video Resolution: 1280×720P, 640x480, 320x240 Video Format: ASF
VII. Recording Video to Local Micro SD Card
>> Please make sure that the camera is added to the APP in LAN or WAN mode before
you start.
7.1. Launch the “ BVCAM ”APP.
7.2. Tap the setting icon on the “ Live video ” page then select " Advance Config " or “ Device
Settings ”.
7.3. Go to “ SD Card Record Config ” page, then set a desired recording mode and file length.
Enabling “
Record sound
” and “
Loop recording
” is also available.
7.4. Tap “ OK ” to complete the SD card recording setting and the camera will record video
to the internal memory.
7.5. The video files will be saved in the internal memory of this camera. You can check out
the video files by following chapter 5.3.
VIII. Resetting
If for any reason the camera stops working or isn’t working properly, you can reset the
camera to restore it back to normal operation.
Operation: When the camera is powered on, press and hold the Reset Button for 3 seconds
until the both blue and red indicator lights turn off. The camera will reboot automatically with
default settings within 1 minute.
IX. Renaming Camera & Changing Password
>> Please confirm that the camera is added to the APP, and it is online in the P2P (LAN)
mode before you start.
9.1. Launch the “ BVCAM ” APP.
9.2. Change the camera name as below:
Step1: Tap the setting icon on the “
Live video ” page then choose “ Modify Device ” or “ Device
Settings
” in the popup window.
Step 2: Clear the default name and type in your desirable name like home, office, bedroom,
etc.
Step 3: Tap “
OK ” or “ √ ” to confirm the change.
9.3. Change the password as below:
OPTION 1
Step 1: Tap the camera icon on the “ Live video ” page, and tap “ Change ” in the popup window.
Step 2: Enter the new password and confirm it, then tap “ OK ” to save the change.
OPTION 2
Step 1: Tap the settings icon on the “
Live video ” page, tap " Advance Config " or “ Device
Settings ”, then go to " Change P2P access password " or “ Change password ” page.
Step 2: Enter the default password “ 8888 ” at first, then enter a new password and confirm it,
tap “
OK
” to save the change.
Frequently Asked Questions
Q1: Why can’t I find the camera’s WIFI signal on my smartphone or tablet PC?
A1: There are 4 solutions to this problem:
1. Plug the camera into an outlet power supply using the power adapter provided. Wait 1
minute for the WIFI signal SSID to appear.
2. Reset the camera (See VIII), then wait for the WIFI signal SSID to show up.
3. Keep your phone or mobile device within the camera’s WIFI hotspot range, refreshing
the WIFI signal page. It may take up to 1 minute for the hotspot to become recognizable
on your phone or mobile device's WIFI setting page.
4. Shut off your phone or mobile device’s WIFI function for a while, then turn it on to search
again.
Q2: Why does the WAN mode setup fail?
A2: Please make sure your network is in a good condition. Plus, the WIFI network the
camera is configured with can’t be the same with one you connect your phone to.
Q3: What can I do if I forget the password?
A3: Please reset the camera. (See VIII)
Q4: The APP cannot find the camera’s UID after choosing “Search (LAN)”?
A4: Ensure your phone or mobile device is still connecting to the camera’s WIFI signal. Ensure
your camera is powered by the outlet power supply or the camera is fully charged.
Q5: Why live video screen shows up black and a searching circle spins in center but nothing
ever displays?
A5: a. If your camera is connected to a slow WIFI network, wait 10-30 seconds for live
video to re-appear.
b. On the live video page, please select a lower resolution to play.
Q6: Live video is not smooth and clear?
A6: Select suitable resolution according to the real time network environment.
Q7: How many mobile devices can connect to the camera at the same time?
A7: No limit.
Q8: There is only 1 user, but the camera shows 2 or more users?
A8: a. If you login in very often, the last login record is still in. If you check it every 2-5 minutes,
the camera will show surely the exact numbers of users;
b. For your safety and privacy, please change camera's password for the fi¬rst time use.
Q9: How many cameras are supported on the mobile application?
A9: No limit.
Q10: Is there any PC client software I can use on my computer?
A10: Please click the PC client software download link and download the zip file on your PC:
http://www.wiseupshop.com/download?name=dvr-0031-4&+++++++
Q11: The camera is not holding my WIFI settings and continues to show that the camera
is offline?
A11: Make sure the camera is inside the range of good WIFI signal. Or check if the power
adapter is connected properly for long time use.
Q12: Will the camera still work if the power goes out?
A12: If the camera is in P2P (LAN) mode, the camera can still work and record video as long
as the camera is still charged. If the camera is in WAN mode, it will not work until the power is
restored and the Internet access is available.
Q13: How to add the camera to more devices?
A13: Make sure that camera is in WAN mode already. Then launch the “ BVCAM ” APP on your
other Android phones or tablet PCs, tap “ + ” icon, input the camera UID (a unique combination
of numbers and letters specific to your camera). Finally, tap “ OK ” to add the camera to the APP.
Q14: What media player software should I use to play back the video files on my
computer?
A14: Click the link: http://www.videolan.org/vlc/index.html to download and install VLC player
to play back video files on your PC or Mac computer.
Q15: How can I read the video files in the internal memory of the camera?
A15: You can go back to the “Live video” page, tap “Record” at the bottom of the screen
and then tap "Remote SD Card" or to view the video files. Or you can download the
video files to your smartphone.