background image

INS_TE(C,U)-FX   

08/12/19

   PAGE 11

INSTALLATION AND OPERATION MANUAL 

TE(C,U)-F SERIES

INSTALLATION CONSIDERATIONS 

These units are supplied as Standalone/Rack mounted module. Units should be installed in dry locations protected from extremes of temperature and 

humidity.

IMPORTANT SAFEGUARDS: 

A)  Elevated Operating Ambient

 - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than 

room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (T

ma

specified by the manufacturer.

B)  Reduced Air Flow

 - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.

SBP-C14 

/ SBP-C03 

CARD CAGE RACKS

CAUTION:

 Although the units are hot-swappable and may be installed without turning power off to the rack, 

Hanwha 

recommends that the power 

supply be turned off and that the rack power supply is disconnected from any power source. Note: Remove electrical connector before installing in 

card cage rack.

1. Make sure that the card is oriented right side up, and slide it into the

 

card guides in the rack until the edge connector at the back of the card seats 

in the corresponding slot in the rack’s connector panel. Seating

 

may require thumb pressure on the top and bottom of the card’s front

 

panel.

  

CAUTION:

 Take care not to press on any of the LEDs.

2.  Tighten the two thumb screws on the card until the front panel of the

 

card is seated against the front of the rack.

WARNING: 

Unit is to be used with a Listed Class 2 power supply.

Summary of Contents for TEC-F Series












Reviews: