
1128600
SmartPAC 2 with WPC 2000 Integration User Manual
2-82
Installation
15.
When the average angle at which the press top-stops falls between 3° and 180°, subtract
the average angle reading from 270°, the Top-stop Angle setting you made on the Press
Control Parameters screen in step 7. The difference is the angle at which the Top-stop
cam turned on, or the Top-stop “On” Angle. Use the boxes in step 3b in the Overrun
Sensor Magnet Installation Worksheet for this calculation.
16.
Turn the Program/Run key switch to PROG, access the Main Initialization Menu (see
Figure 2-38, page 2-73) by pressing the 1 and CLEAR keys at the same time for a second
or two, and select PRESS CONTROL to display the WPC Initialization Menu.
17.
Select PRESS PARAMETERS on the WPC Initialization Menu to display the Press
Control Parameter Menu.
18.
Enter the Top-stop “On” Angle value you calculated in step 14 or 15 in the TOP STOP
DEFAULT field on the Press Control Parameter Menu (see page 4-27 for instructions).
Installing the Overrun Sensor Magnet
The following procedure shows you how to
•
Determine the correct angle at which to mount the overrun magnet, based on your Top-stop
“On” Angle calculations in the previous section
•
Determine the setting for option switches 1 and 2, based on your Top-stop “On” Angle
calculations
•
Install the magnet
Since the Top-stop cam stays on for 20°, the magnet must be mounted at an angle at least 20°
greater than the Top-stop “On” Angle you calculated and set in the previous procedure,
allowing the Top-stop cam to turn off before the overrun limit sensor turns on. Otherwise, an
“80” series fault will display on the SmartPAC 2 LCD (see
Perform the following steps:
1.
Determine the angle at which to install the overrun sensor magnet by consulting
Table 2-26. The first row of the table, labelled “Top-stop “On” Angle,” shows Top-stop
“On” Angle ranges (i.e., less than 240°, 241° to 270°, etc.). The second row shows the
angle at which the overrun sensor magnet should be mounted for each range (i.e., at 270°
if the Top-stop “On” Angle is less than 240°, at 300° if the Top-stop “On” Angle is
between 241° and 270°, etc.).
Table 2-26. Overrun Sensor Magnet Mounting Angle and Option Switch Settings
Top-stop “On” Angle
< 240°
241° to 270°
271° to 300°
> 301°
Magnet Mounting Angle
270°
300°
330°
359°
Switch 1 Setting
ON
ON
OFF
OFF
Switch 2 Setting
ON
OFF
ON
OFF
Summary of Contents for SmartPAC 2
