WINTACT WT63A User Manual Download Page 10

-16-

                                    Warning

When making measurements on exposed rotating 

parts or power train parts of machinery, proceed 

with utmost care to prevent accidents due to getti-

ng caught in the machinery.

3.Other items

Attentions

                                    Caution

If  the unit shook excessively, the receiver may 

produce extremely high sound pressure that 

hurts human ear , be careful in process of using

the signal output plug.   

Warranty

1. About relative warranties please read warranty card.

2. We disclaim any liability due to: client's transportation 

    damages; incorrect use or operation; manipulation, 

    alterations or repair attempts; without  warranty card, 

    invoice.

-17-

Maintenance 

1. Replacement and upkeep of battery:

a. After power on, if an icon          appears on the LCD,

    you need to replace the battery immediately, for details 

    please refer figures and contents on page 9 of this 

    manual. 

b. Remove the battery from the unit if it is not required for 

    extended periods of time in order to avoid damage to 

    the battery compartment and the erosion resulting 

    from a  battery leakage.

2. Do not store or use the unit in following circumstances:

a. Splashes of water or high levels of dust.

b. Air of  high salt or sulphur content.

c. Air mixed with other gases or contents.

d. High temperature or humidity (above50

, 90%,) or 

    direct sunlight.

3. Do not disassemble the unit or attempt any internal 

    alterations.

4. Never use alcohol or diluents to clean the  housing

    for doing that will especially erode the LCD surface;

    just clean  the unit lightly as needed with little clean

    water.

Note

We reserve the right to change the product design or 

change the manual, without prior notice

Summary of Contents for WT63A











Reviews: