WinSystems PCM-VDX-2-512 Product Manual Download Page 13

Page: 13 / 75

140808

PRODUCT

MANUAL

PCM-VDX-2-512

FUNCTIONALITY

I/O Port Map

Following is a list of I/O ports used on the PCM-VDX-2-512. I/O addresses marked with a ** are generally unused and

should be the first choice in I/O address selection for external I/O boards.

NOTE:

The PCM-VDX-2-512 uses a PnP BIOS resource allocation. Care must be taken to avoid contention with resources allocated by the BIOS.

HEX Range

Usage

0000h-000Fh DMA 8237-1

0010h-0017h Reserved Redundancy

0018h-001Fh Free

0020h-0021h PIC 8259-1
0022h-0023h 6117D configuration port

0024h-002Dh Free

002Eh-002Fh Forward to LPC BUS
0030h-003Fh Free

0040h-0043h Timer counter 8254
0044h-0047h Free

0048h-004Bh PWM counter 8254

004Ch-004Dh Free

004Eh-004Fh Forward to LPC Bus
0050h-005Fh Free

0060h Keyboard data port
0061h Port B + NMI control port

0062h-0063h 8051 download 4K address counter

0064h Keyboard status port
0065h Watchdog0 reload counter (Vortex internal WD)
0066h 8051 download 8-bit data port
0067h Watchdog1 reload counter (Vortex internal WD)

0068h-006Dh Watchdog1 control register (Vortex internal WD)

006Eh-006Fh Free

0070h-0071h CMOS RAM port
0072h-0075h MTBF counter
0076h-0077h Free

0078h-007Ch GPIO port 0,1,2,3,4 default setup
007Dh-007Fh Free

0080h-008Fh DMA page register

0090h-0091h Free

0092h System control register

0093h-0097h Free

0098h-009Ch GPIO direction control
00A0h-00A1h PIC 8259-2
00A2h-00BFh Free

00C0h-00DFh DMA 8237-2

00E0h-00FFh Free

0100h-0101h GPCS1 default setting address

0102h-016Fh Free

0170h-0177h Reserved IDE1

01E8h-01ECh Reserved

01EDh Status LED

01EEh-01EFh Watchdog Timer Control (Legacy)

Summary of Contents for PCM-VDX-2-512












































































Search results

Summary of Contents for PCM-VDX-2-512

Reviews:

Related manuals for PCM-VDX-2-512

Brands by name

Popular brands

WinSystems PCM-VDX-2-512, Product Manual

Search results

Summary of Contents for PCM-VDX-2-512

Reviews:

Related manuals for PCM-VDX-2-512

Brands by name

Popular brands