background image

 

11

PROGRAMMING OPTIONS 

OPTION 1: TACH FINE TUNING ( SEE EXAMPLE # 3 )  

Occasionally with the AUTO TACH learning feature, you may not reach exact performance on the first try. This option 
allows you to fine-tune the TACH signal manually. 

OPTION 2: CRANKING ADJUSTMENT 

If you expect that the vehicle needs adjusting you can force the starter to slightly under crank or over crank. This adjustment may 
be necessary in some older vehicles or vehicles with diesel engines to help the engine start in extremely cold weather conditions. 

OPTION 3: AUTOMATIC OR MANUAL VEHICLE - FACTORY DEFAULT SETTING ( SEE EXAMPLE # 4 )  

By default, the system is delivered for use on a MANUAL transmission. To use the system with an AUTOMATIC transmission, 

cut the ORANGE jumper before powering ON

 the module then access this option to select AUTOMATIC. 

This option also allows you to reinitialize the system back to factory default. You have to perform a TACH learning, 
otherwise you can not start the vehicle by remote. 

OPTION 4: RUNNING TIME DURATION 

This option allows you to set the remote start engine running time for 5, 15 or 30 minutes. When remote started, the engine 
will run for the selected amount of time. 

OPTION 5: POWER AUXILIARY OUTPUT 

This option allows you to set the AUXILIARY OUTPUT as: 

1

: 2

nd

 ignition (default)    

2

: 2

nd

 accessory  

 

3

: 2

nd

 starter 

 OPTION 6: GLOW PLUG WAITING TIME ( FOR DIESEL ENGINE ) 

Diesel engines need to warm up glow plugs before starting. Turn ignition key ON and count how many seconds it takes for 
the glow plug light to turn OFF then select the closest waiting time. 

 

Summary of Contents for WS-07U




















Reviews: