background image

WR-ARP-ELAZ-100 and WR-RCU-100 Technical User’s Guide 

 

 

 

Rev. F

 

6. Rotator System Bench Testing 

Note:  Before doing the final mechanical rotator installation it is important that 

the rotator system is first set up, calibrated and tested on a workbench. This is 

to ensure that the rotator control unit determines the mechanical limits of the 

rotator  without  physical  obstruction,  and  that  the  Manual  Tracking  Controller 

software positions the rotator azimuth and elevation shafts to their zero points. 

  

1.  Remove the small cover (with two plastic glands) on the rotator to gain access 

to the two terminal blocks inside. 

 

2.  Temporarily connect the azimuth motor cable to the azimuth terminal block of 

the rotator as shown in Table 2. 

 

3.  Temporarily connect the elevation motor cable to the elevation terminal block 

of the rotator as shown in Table 3. 

 

4.  Switch on the rotator control unit power. 

 

5.  Start the Manual Tracking Controller software. There should be an icon on the 

desktop if you chose to install one. Alternatively, you can find the application 

by clicking Start … Programs … WiNRADiO … WR-RCU-100.  

 

6.  The software should detect that a rotator calibration is required and then start 

the process automatically. If it does, please wait until it is finished. This may 

take a few minutes. 

 

7.  Click Tools … Diagnostics and observe that there are no faults. The last field 

on the window should read “Calibration:    Done”.  

 

8.  Click Tools  Offsets and ensure offsets are set to zero. 

 

9.  Now switch off the power and prepare for rotator installation. 

 

 

Note:  The Manual Tracking Controller software auto-detects the WR-RCU-100 

rotator control unit. If at first the hardware is not detected, switch the control 

unit  power  off  and  back  on  again.  This  should  cause  the  “Found  new 

hardware” wizard to start. 

 

Summary of Contents for WR-ARP-ELAZ-100

























Reviews: