background image

WR-ARP-ELAZ-100 and WR-RCU-100 Technical User’s Guide 

Rev. F

13 

9. Software Operation 

9.1. Rotator Selection  
 

Multiple copies of the Manual Tracking Controller software application can be run on 

a single computer simultaneously. This provides the ability to control more than one 

rotator  from  the  same  computer.  Each  software  application  instance  must  have  a 

matching WR-RCU-100 rotator control unit associated with it. 

 

When  the  software  application  is  started,  it  automatically  searches  for  available 

rotator  control  units  connected  to  the  computer  via  USB.  If  an  unassigned  unit  is 

found,  control  will  be  allocated  to  it.  If  several  unallocated  units  are  found,  the 

software will open a window showing all available controller units listed by their serial 

numbers. The user then selects the desired unit from the list: 

 

 

 

 

If  no  control  unit  is  found,  the  software  will  open  a  message  window  and  alert  the 

user.  If  the  Ignore  button  in  this  window  is  clicked,  the  software  will  default  to 

operating  in  demo  mode  only.  While  in  demo  mode,  controls  are  disabled  and  a 

dynamic menu item "Select rotator control unit" appears under the File menu. 

 

Summary of Contents for WR-ARP-ELAZ-100

























Reviews: