manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

The WinGD X62DF maintenance manual is available for download for free on our website. This comprehensive manual provides all the information needed to properly care for and maintain your engine. Download it now from manualshive.com to ensure long-lasting performance of your WinGD X62DF engine.

Share
Download
background image

13.3.3

HP fuel pipe (fuel rail to injection valve) - grind the sealing face

Periodicity

Description

Unscheduled
Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

0.5 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Intermediate

1

Support equipment

Description

Part No.

CSN

QTY

Grinding tool

94871

1

Stencil

94871A

1

Hand drill

NA

1

Supplies

Description

QTY

Emery paper (different grades)

AR

Polishing cloth

AR

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

•

None

PRELIMINARY OPERATIONS

•

The HP fuel pipe must be removed, refer to section 

13.3.2 HP fuel pipe (fuel rail to

injection valve) - remove

X72DF

AA00-8733-00AAA-655A-A

Maintenance Manual

HP fuel pipe (fuel rail to injection valve) - grind the sealing face

Winterthur Gas & Diesel Ltd.

- 748 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X62DF

BAFANG H550 Manual preview
H550
Brand: BAFANG Pages: 5
Stobag MOVENO DWIR-E Installation And Use Instructions And Warnings preview
MOVENO DWIR-E
Brand: Stobag Pages: 40
Habasit Rossi HB Operational Manual preview
Rossi HB
Brand: Habasit Pages: 54
Briggs & Stratton 90000 I/C 525 Series Operator'S Manual preview
90000 I/C 525 Series
Brand: Briggs & Stratton Pages: 16
Exalto MD1 223BDC Manual preview
MD1 223BDC
Brand: Exalto Pages: 28
Mile HaoXianG Model Technology DLE-20 User Manual preview
DLE-20
Brand: Mile HaoXianG Model Technology Pages: 3
Man E 2942 LE 302 Repair Manual preview
E 2942 LE 302
Brand: Man Pages: 18
GR GR6 Series Manual preview
GR6 Series
Brand: GR Pages: 8
O.S. engine OCA-3100HV Instructions preview
OCA-3100HV
Brand: O.S. engine Pages: 2
Lycoming TEO-540-A1A Installation And Operation Manual preview
TEO-540-A1A
Brand: Lycoming Pages: 120
Volvo TAD734GE User Manual preview
TAD734GE
Brand: Volvo Pages: 72
Dongfeng Chaoyang Diesel engine Co CYQD 32 Series CYQD32 Service Manual preview
CYQD 32 Series CYQD32
Brand: Dongfeng Chaoyang Diesel engine Co Pages: 60
Ingersoll-Rand 3IRL2N Workshop Manual preview
3IRL2N
Brand: Ingersoll-Rand Pages: 127
New Holland F4CE9484 Service Manual preview
F4CE9484
Brand: New Holland Pages: 41
Asmo Marine Thoosa Installation Manual preview
Thoosa
Brand: Asmo Marine Pages: 8
ZIEHL-ABEGG ECQ Assembly Instructions Manual preview
ECQ
Brand: ZIEHL-ABEGG Pages: 17
Ford LSG 875 Service Manual preview
LSG 875
Brand: Ford Pages: 173
Nanni N4.60 Instruction Manual preview
N4.60
Brand: Nanni Pages: 12

Brands by name

Popular brands

Load more brands