5
6
Automatic Operation for DISH Users
1 Operation
1
4
2
3
Operation 2
Manual Operation
5
1
3
4
6
2
The TRAV’LER interface box will try
to determine the type of dish that it is
working with. The TRAV’LER interface
will display the type of satellite dish on
the top line.
The TRAV’LER interface offers a simple one button operation. This one button operation is used for both general
operation and for selecting the antenna type. The steps below show the screens that will be displayed as the TRAV’LER
antenna searches for satellites. For steps on how to set up the TRAV’LER antenna for Bell TV, see pages 3–4.
The TRAV’LER antenna will enter the search
mode as part of its normal operation.
Press and hold
[POWER]
for two
seconds or until the TRAV’LER interface
displays “POWER ON.”
Now that the power is on, release the
[POWER]
button.
The TRAV’LER will find its home
position. Then, it will begin to look for a
satellite. When the TRAV’LER antenna
finds a satellite, it will peak on the signal
and determine which satellites have
been found. Once the TRAV’LER knows
which satellites have been found, it
moves to the correct satellite(s).
TIP
If you want to turn off the power to the TRAV’LER antenna after the antenna has locked onto satellites, press
[POWER]
and
[SELECT]
at the same time. Before traveling, make sure to press
[POWER]
and wait for antenna
to start to power up. Then press
[POWER]
again to initiate the stow sequence. See page 6 for more information on
stowing before traveling.
Continue to page 5 if setting up the receiver for the first time or if setting up the receiver after moving the receiver
from the house to the RV. If the receiver is already set up in the RV, you are now ready to watch TV!
In automatic search mode, the TRAV’LER
antenna will lock onto three different
satellites. As the antenna finishes
searching, the antenna will display an
asterisk for each satellite found.
The TRAV’LER antenna is a versatile satellite antenna and can be manually set to find many different satellites
individually. The instructions below assume that the TRAV’LER antenna is already in the stowed position. Note: this
function is rarely used.
The TRAV’LER interface will ask if
you want to turn the power off. Press
[ENTER]
to choose “No” and start a new
search for your chosen satellite. Press
[SELECT]
then
[ENTER]
to choose “Yes”
and turn off the antenna.
The TRAV’LER antenna will remain in
manual mode until you select “Multi-Sat
Mode” again.
The TRAV’LER interface will ask you to
confirm the change. Press
[SELECT]
to move the asterisk to “Yes.” Then,
press
[ENTER]
.
The TRAV’LER interface will then
acknowledge which satellite has been
selected. Press
[ENTER]
.
Once in the Search Menu, you may
choose from the following: MULTISAT
MODE (normal search mode), MANUAL
110, MANUAL 119, MANUAL 129, MAIN
MENU (returns to the User Menu), or
EXIT (enters the search routine).
NOTE
MANUAL 82
&
91 will be
options for BELL TV users.
Press
[SELECT]
to cycle through these
satellites until the asterisk is next to the
satellite you wish to find. Then, press
[ENTER]
to select a satellite.
The User Menu consists of four choices:
Search Mode
, Diagnostics, Installation,
and Exit.
NOTE
Diagnostic and Installation
menus are not required for
normal operation and should only be
entered by a trained professional.
Press
[ENTER]
to choose Search Mode.
Press and hold the
[ENTER]
button for
two seconds. The TRAV’LER interface
will ask if you wish to enter the User
Menu. Press
[SELECT]
to choose “Yes.”
Then, press
[ENTER]
.
Press and hold
[POWER]
for two
seconds or until the TRAV’LER interface
displays “POWER ON.”
WINEGARD COMPANY
POWER ON
connecting to
antenna
SM Dish 1000
Ready: Multi-Sat
SM Dish 1000
Searching...
SM Dish 1000
*119 *110 *129
SM Dish 1000
Home EL
WINEGARD COMPANY
POWER ON
Enter User Menu?
*Yes No
Search Mode*
Diagnostics
Multi-Sat Mode*
Manual 61
Power OFF?
*Yes No
Manual ##
Selected