background image

2

DIRECTV

®

 is an official trademark of DIRECTV, a unit of GM Hughes Electronics Corporation.

DISH Network

TM

 is an official trademark of EchoStar Communications Corporaton.

DIGITAL BROADCAST SYSTEM
SATELLITE(S)

Introduction

Congratulations! You have purchased one of
Winegard’s latest developments in the mobile satel-
lite reception product line —the Movin’ View

TM

.

This system, used with your digital satellite receiver,
will deliver the best reception possible using GPS
(Global Positioning System) and precision gyro-
scopes.

How  Does Digital Satellite
TV Work?

Satellite programming originates from an “uplink”
facility on Earth — the facility receives many signals
from different sources, combines the signals digitally
and transmits to the satellites. The satellites (22,300
miles above Earth) receive the uplink signal, amplify
it and then transmit it back to earth in the
Ku frequency band. This signal
is concentrated and reflected to
the LNBF* located at the “focal
point” of the dish. The LNBF
amplifies and converts the signal to
the 950 to 2050 MHz range. The signal
is then passed through a coaxial cable
to the receiver where individual chan-
nel selection and processing take
place.

For Programming information call:
DISH NETWORK

TM

 - 1-800-333-DISH (1-800-333-3474)

DIRECTV

®

 - 1-800-DIRECTV (1-800-347-3288)

ExpressVu 

TM

 1-888-SKY-DISH (1-888-759-3474)

Your new Winegard RV Digital Satellite System is an easy-

Introduction/How Does Digital Satellite TV Work?

PROGRAMMING UPLINK

CONTROL CENTERS

HIGH POWER KU-BAND
DOWNLINK SIGNAL

WINEGARD DIGITAL SATELLITE
SYSTEM ANTENNA

RECEIVER

UPLINK SIGNAL

TELEVISION
SET

to-use satellite TV reception system. Because it mounts
on the top of your recreational vehicle, it goes where you
go and provides quality reception of digital satellite sig-
nal in the continental United States only.

* Low Noise Block Converter Feed

Summary of Contents for Movin' View MV-0500













Reviews: