background image

18 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No.

PROBLEM

CAUSES & SOLUTIONS

Noise can come from the coolant, which is normal.

At the end of each cycle, you can hear a gurgling sound 
caused by the coolant.

The expansion and contraction of the interior walls can cause 
creaking noises.

The unit is not level.

The installation measures were not respected, leaving too 
much space between the cellar and the cabinets and 
amplifying the noise of the compressor and the fan at the 
back.

The ceiling height and the size of the room (open area) may 
also increase the sound (echo effect).

The unit is not level.

The door was reversed and installed incorrectly.

The door is open but the lock is locked.

The gasket is dirty.

Shelves are improperly installed on the rails or bottles that are 
too large or improperly placed prevent a shelf from closing.

Adjust the leveling feet at the front until the door is equal to 
the cellar. 

The hinge screws are not tight enough; replace the door 
equal to the box and tighten the screws.

11

A shelf in my cellar is not level. Make sure that the shelf is properly secured on its rails. 

Check that the drain is in the evaporation tray at the back of 
the cellar. If so, during very humid periods, you may need to 
soak up the excess water in the pan.

Make sure the cellar is leveled from front to back and left to 
right.

13 Water collects inside my cellar.

This is a phenomenon observed especially in summer due to 
humidity. Check that the door seal is watertight. During very 
humid weather, it is recommended to sponge off the excess 
water that forms inside your cellar and if necessary in the 
back pan near the compressor.

14

There is frost on back wall of 

my cellar.

This is a very normal phenomenon when water vapours 
freeze. However, when the cooling cycle ends, the ice melts 
and runs down the drain. These drops normally evaporate.

15

There is steam / humidity 

between the thermal windows 

of my cellar.

During very wet periods, mainly in summer, this can happen.

16

The digital display shows HH or 

LL and a continuous beep is 

heard.

The temperature sensor is non-functional and must be 
replaced.

12

There is water on the floor of 

my cellar.

8

My cellar seems to be making 

too much noise.

9

The door does not close 

properly.

10

The door of my cellar is not 

equal to the box.

Summary of Contents for Platinum WC46PLDZ5






















Reviews: