background image

CONTROLS

3-7

                           

STRIDE2 36V (SS) 98745  11/08/99

9.  DIRECTIONAL CONTROL LEVER

Controls the machine direction, and scrub
brushes and solution flow.

To propel machine forward, push the lever
forward.

To propel machine backward, pull the lever
toward you.

The scrub brushes will not rotate and the
solution will not flow to scrub deck with the
directional control lever in neutral.

10. SPEED CONTROL KNOB

Controls the speed of the machine.

To increase speed, rotate knob clockwise.

To decrease speed, rotate knob
counterclockwise.

11. BATTERY CHARGE LEVEL INDICATOR

Indicates the charge level of the batteries.

The meter display is divided into 10 vertical
bars.  Bars illuminated on the far right indicate
full charge.  Bars flashing near the left side
indicate the batteries should be recharged.
Further operation of the machine could
damage the machine or the batteries.

When the machine is left overnight with less
than a full charge, the display may initially
indicate a full charge.  It will also indicate a full
charge if the batteries are disconnected, then
reconnected.  After a few minutes of operation
the meter will give the correct charge level.

12. EMERGENCY SHUT-OFF SWITCH

(OPTIONAL)

Shuts off machine.

To shut off machine, push the switch.

To restart machine, rotate the switch
clockwise.

13. HOUR METER (OPTIONAL)

Records the number of hours the machine has
been in operation.  This information is useful
in determining when to service the machine.

14. CIRCUIT BREAKERS

Circuit breakers interrupt the flow of power in
the event of an electrical overload.  When a
circuit breaker is tripped, reset it by pressing
the exposed button.  If a circuit breaker
continues to trip, the cause of the electrical
overload should be found and corrected.

3 Amp.  Protects the machine
controls.

30 Amp.  Protects the left scrub
brush motor.

30 Amp.  Protects the right scrub
brush motor.

25 Amp.  Protects the vacuum
motor.

35 Amp.  Protects the propel 
motor.

15. PARKING BRAKE PEDAL (OPTIONAL)

Locks front wheels to prevent unintentional
movement.

To set parking brake, push down on the foot
pedal.

To release parking brake, pull up on the foot
pedal.

Summary of Contents for STRIDE 2


























Reviews: