background image

OPERATION

MB2000I  980071  11/15/02

  3-3

!

CAUTION

CONTROLS

1.  Safety Lock – 

Prevents unintended operation of

the machine.

2.  Switch Levers – 

Turns machine on/off.

OPERATION

For indoor use only.

When using the pad, always keep the machine
moving when in contact with the floor.

High starting torque. Hold machine firmly with
both hands.

1.  Ensure that the pad driver is in good shape.

Install or change pad if necessary.

2.  Plug the machine into a wall outlet as described

in the grounding instructions.

3.  Release latch, lower the handle and move into

position.

4.  Push the safety lock forward, unlocking the

switch levers.

5.  With the safety lock forward, squeeze one or

both of the switch levers, turning the machine
on. (These levers can be operated
independently of each other). The safety lock
will not re-engage until both levers are released.

6.  To stop the machine, release the switch levers.

7.  Do not let machine rest on pad.  When finished

with the machine, return handle to the storage
position.

NOTE:  The machine is equipped with a circuit
breaker to protect the motor in the event an overload
condition occurs. The circuit breaker is located on
the side of the motor. Push the reset button to
restart the machine. If the breaker trips again,
correct the cause of overloading before proceeding.

DAILY MAINTENANCE

1.  Inspect power cord for wear. To prevent

electrical shock replace cords with frayed or
cracked insulation immediately.

2.  Place machine in the storage position.

3.  Check pad condition. Change if soiled or torn.

PAD INSTALLATION

1.

  

Lay machine back, exposing the under side.

2

2

1

!

WARNING

Ensure pad is center on pad driver.  Pull pad
to edge of pad driver in several directions to
check for proper engagement.

NOTE:  Use care when replacing center lock
to prevent cross threading.

!

WARNING

HANDLE
RELEASE LATCH

Summary of Contents for MB2000I



























Reviews: