WilTec 62455 Operation Manual Download Page 10 | Manualshive

Page: 10 / 11

background image

Code Removal

Attention!

All coded transmitters are affected, if code removal is performed for one of them, causing

all previously entered codes to become invalid.

Code Reversal

Inching Operation

During inching operation the motor will continue to operate after the “Up” or “Down” buttons have been
pressed for less than 1.5 seconds. This will cause the shutter to be completely raised or lowered after
shortly tapping one of the buttons. The operation of the motor will thereby proceed until it either
reaches a set limit or the “Stop” button is pressed.

© by WilTec Wildanger Technik GmbH

Artikel 62455-62460

Seite 10

http://www.WilTec.de
http://www.aoyue.eu

11 2020

-1

http://www.teichtip.de

«
...
8
9
10
11
»

Summary of Contents for 62455












Reviews:

No comments

Related manuals for 62455

Brand: Parker Pages: 36

Brand: Kubota Pages: 285

950-1020 MOTOR KIT 8504048 REV 2 1297

Brand: TJERNLUND Pages: 2

Brand: Jiecang Pages: 2

Brand: Grundfos Pages: 13

Brand: Briggs & Stratton Pages: 200

Brand: Hacker Pages: 8

Brand: Hacker Pages: 8

Brand: Hacker Pages: 38

Brand: Stober Pages: 6

Brand: DANA Pages: 3

Brand: DANA Pages: 3

BLACK BLOCK 62-SGW

Brand: TOMAHAWK SPORT Pages: 20

Brand: Black Bruin Pages: 4

Brand: Bosch Rexroth Pages: 56

Brand: Desert Aircraft Pages: 9

Brand: KTM Pages: 145

Brand: CRRCpro Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands