background image

 

3. Symbols on the machine

For safe operation and maintenances, symbols are carved in relief on the machine.
According to these indications, please be careful not to make a mistake.

( a)  The port to refuel the „MIX GASOLINE“

Position: fuel tank cap

( b)  The direction to close the choke

Position: AIR CLEANER COVER

( c)  The direction to open the choke

Position: AIR CLEANER COVER

4. Safety Precautions

 Before using the device

 a. Read this owner‘s manual carefully to understand how to operate
this unit properly
 b. This product has been designed for use in cutting grass, ad it
should never be used for any other purpose.
 c. You should never use the product when under the influence of al-
cohol, when suffering from exhaustion or lack of sleep.
d. Avoid running the engine indoors. The exhaust gases contain
harmful 

  carbon monoxide

e. Never use the product under circumstances like those described
below:
 1. When the ground is slippery or when other conditions exist which
might make it not possible to maintain a steady posture
2. At night, at times of heavy fog, or at any other times when your
field of vision might be limited and it would be difficult to gain a clear
view of the area.
3. During rain storms, during lightning storms, at times of strong or
gale- force winds, or at any other times when weather conditions
might make it unsafe to use this product.
f. When using this product for the first time, learn to handle it from
skilled worker.
g. Lack of sleep, tiredness, or physical exhaustion results in lower at-
tention spans, and this in turn leads to accidents and injury. Limit the
amount of time of using the machine continuously to somewhere
around 10 minutes per session and take 10~20 minutes of rest be-
tween work-sessions.

© by WilTec Wildanger Technik GmbH 

Seite 24 

http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

Summary of Contents for 61495


















Reviews: