WilTec 50799 Operation Manual Download Page 4

 

© by WilTec Wildanger Technik GmbH 

 

Item 50799

 

Page 4 

 

http://www.WilTec.de

 

http://www.aoyue.eu

 

 

 

02 2022

-1

 

http://www.teichtip.de

 

out of order instantly 

until it has been repaired by a specialist. It is recommended to have the device 

checked at least once a year by a specialist.

 

 
 

Installation

 

 

1.

 

Mount the hydraulic cylinder to the mounting plate with screws, washers, and nuts. Make sure 
that the discharge is not damaged during this process.

 

2.

 

Place the upper end of the lifting cylinder into the lifting frame and fix it with the bolt.

 

3.

 

Install the foot pedal to the hydraulic cylinder and fix it with an M8×30 screw.

 

4.

 

Place the handle in the intake of the lifting frame and secure it with a bolt.

 

5.

 

The locking bar needs to be locked into one of the positions when lifting weights. If this is not 
the case, it can lead to damage of the jack lift or to serious injury.

 

6.

 

Check whether all screws are tightened. Then make sure that the tip of the locking bar is behind 
a notch of the frame.

 

 

 

 

Name

 

 

Name

 

1

 

Locking bar tip

 

2

 

Frame notch

 

 
 

Operating Instructions

 

 

Lifting objects

 

 

1.

 

Only use the jack lift on an even and solid surface.

 

2.

 

To prevent the loaded object from slipping during the lifting process, centre the weight evenly.

 

3.

 

Place the jack so that the lifting saddle is placed centrally under the object needing to be lifted.

 

4.

 

Operate the foot pedal until the lifting saddle touches the object to be lifted. Fix the castor rollers. 
Before raising the load, check that the lifting saddle and weight are in the right position.

 

5.

 

Secure the object with lashing straps.

 

6.

 

Repeatedly use the foot pedal to lift the object. Make sure that the locking bar tip properly locks 
into a notch of the frame when the desired height is reached.

 

7.

 

Stabilise the jack lift on an even surface by adjusting the stabilisation screw.

 

 

Summary of Contents for 50799








Reviews: