Williams Sound PERSONAL PA Pro Wide-band System 275 User Manual Download Page 7

Page: 7 / 28

Williams Sound

Helping People Hear

Phones

PPA T4 Professional FM Auditory Assistance Transmitter

Williams Sound

Power

-12dB -6dB

0dB

+6dB

Audio Level

Increase

Decrease

Too Hi

Audio Adjust

RF Carrier

Frequency Synthesized, Channel-Selectable

Phones Jack

1/4" jack, 220

source impedance. Drives mono or stereo

headphone. Monitors exactly what is being transmitted.

Power On Indicator

Green LED

RF Indicator

Green LED indicates transmitter RF is on

Audio Level Indicators

Four-LED array shows audio level in 6 dB steps. Optimum level
is reached when the amber

light usually blinks and the red

light blinks occasionally.

Audio Level Control

Rotary pot, screwdriver adjust,
used with audio level indicator lights

Model PPA T4 Auditory Assistance FM Transmitter

Line Out

FM Channel,

Power

Power: 24 VAC,

50-60 Hz, 10VA

Williams Sound Corp., Minneapolis, MN USA

(XLR) Bal. Mic

Bal./Unbal line or 70V

(TRS) Bal./Unbal .

Line or 70V

Audio Input

Antenna

75 Ohms

Plug

Audio Select

See chart on top.

To configure, see chart on top.

1 2 3 4 5 6 7 8

Balanced/Unbalanced Audio Input

Combination 3-pin female XLR/1/4" stereo jack, accepts
balanced or unbalanced microphone and line level inputs,
25 V or 70 V audio input

IMPORTANT: If you choose to connect to 70 Volt
Speaker line, be certain to set the Audio Select switch
correctly. Transmitter damage will occur if you do not.

Audio Select Switches

DIP switch, sets input characteristics, audio
processing mode, and input filter cutoff
frequency. (See top panel chart or Figure 3)

Line Out

Line level output of the fully
processed, as transmitted, audio.
Can be used for monitoring,
recording, or as a feed for other
equipment.

Power
Connection

3-pin, Molex
connector for TFP
016 power supply

FM Channel/FM Power Switches

DIP switch for setting channel frequency and
RF output power level. See chart on top of
unit for switch configurations (Fig. 3, page 8).

IGURE

2: T4 T

RANSMITTER

ONTROLS

& F

EATURES

Summary of Contents for PERSONAL PA Pro Wide-band System 275





























Search results

Summary of Contents for PERSONAL PA Pro Wide-band System 275

Reviews:

Related manuals for PERSONAL PA Pro Wide-band System 275

Brands by name

Popular brands

Williams Sound PERSONAL PA Pro Wide-band System 275, User Manual

Search results

Summary of Contents for PERSONAL PA Pro Wide-band System 275

Reviews:

Related manuals for PERSONAL PA Pro Wide-band System 275

Brands by name

Popular brands