you have to install the driver firstly which will be available downloading from the dealer
’
s web-site. The first time after installed the driver, connect the camera
to your computer, the computer will detect a new USB device has been connected and try to looking for a driver. After a driver installation is done, the
PC-Cam function will be available which you can ready to upgrade the existing on board FW. Please refer the further instruction which will be provided your
dealer to finish the FW update processing.
7. Downloading photos/ Movies to your
computer
Press CAM-PW to turn the camera ON manually
at the LIVE mode.
- Connect your computer and the camera with
USB cable.
-
A pop up to show the mobile hard disk
which is assigned for the camera
device.
-
For example:
“
H
”
or
“
I
”
:\DCIM\100MEDIA
-
Click into the proper directory to see all
files inside.
8.
MOUNTING DEVICE
Before starting to put this camera in the field for scouting game, the camera must be mounted in a certain place properly or on a tree whose diameter will
not be less than 6 inch (15cm) and located not higher than 1M with your desired mounting method that following the installation method as shown as below.
The design is reserved to fit for two ways of mounting.
8-1 Belt Mount
: This belt is attached in the packing.
See Fig.5
8-2 Python Adjustable Locking Cable (Not including in this packing):
See Fig. 6
You can able to use a Python adjustable locking cable to provide more security to your WildSpy
Cam. The
“
Master Lock
”
brand is a good choice.
8-3 Belt Mount with Metal Bracket and U locked
: (Optional Accessory )
See Fig. 7
With an optional choice, a steel mounting bracket and U type security bar can be used to
provide stronger security ability. You can buy this accessory from your local dealer.
9. CONNECT An External wireless Invisible IR Booster
For an experienced user, you always would expect to get extreme quality pictures and videos by
many skills. WldSpy Cam provide an option that the wireless booster like
IRX-22BW
will enhance
the camera simply. Thus, you will get several times higher illumination depend on a number of
boosters to be configured.
Refer to the user guide and snap the transmitter to the belt or Python easily. Set the IR trigger
Sensor against the IR light source on the camera. Just need a single transmitter to control unlimited
wireless boosters which they will be set with same frequency around 100 feet.
9 . USE LENS HOOD
This lens hood is come with the packing that is used for installing on the camera lens to prevent sun light reflection too much into the camera sensor
and snow as well as rain or snow-fall stacked in front of the lens.
10.
Solar Power Pack Connection:
If you also have bought a Solar Power Pack ( Model: SO6-6W-9V), plug the Solar pack controller cable to the Solar PW port on the camera unit simply.
Touch the PW button on the controller to supply the solar power to the camera. The solar powered pack will always supply energy in 24/7 and will be charged
under sun light automatically. It isn
’
t a matter there are some days with cloudy because a high capacity storage power pack will support this camera to work
for more than 10 days or a few thousand shots after one time of fully charged on the Solar Pack.
11.
Power Management:
It is an optional but highly recommended to install all Alkaline batteries into the camera compartment even you prefer to always use a solar system. The
backup battery dose stand by only while the solar pack energy still be enough to support Camera operation as usual. Batteries will be drained since the
power pack goes to the OFF w/o any charging for a long time. It is ideal for remaining the scouting settings even no more supply from Solar pack.
Troubleshooting Guide /Useful Skills
12-1 No animal showing in some pictures:
- Check if the unit is pointed the direction where the sun is rising or sunset that the sensor might be triggered.
- The PIR sensor may detect an animals through vegetation out of view from the camera.
- If the animal was moving quickly, camera may not capture it in time while an animal still staying in the zone.
- Make sure that the unit was mounted on a steady tree or other place that does not wobble.
12-2 The Camera In-Use light is remaining ON, but the camera does not respond:
- The camera may be time-out and shut down automatically. Repeat to press the CAM-PW to resume the camera ON.
- Battery may be too lower that could not support the camera operation. Check the battery icon for the level.
- The Trigger Time is set on the FAST mode. You have to switch OFF the main PW and back ON.
12-3 The CAM-PW switch does not respond:
Attempt to turn the camera ON too quickly after the main power ON. Wait for about 10 seconds until the back light of scouting LCD goes to OFF. Then try
again.
12-4 Don
’
t satisfy a brightness on night Pictures. It seems too dark
-You might set the Shutter / ISO to be FAST, try to change for AUTO or add an external booster.
-Batteries may too lower or quality is not good or they are not Alkaline type that the battery set could not afford a high current consumption moment when
the internal IR light was ON. Need to replace with a good quality brand new battery set.
