manualshive.com logo in svg

Wildix WSG08POE, User Manual, Page: 28 / 34

Share
Download
Wildix WSG08POE User Manual Download Page 28

➤

 Max Age: The  maximum  time  (in  seconds) a device  can wait without receiving  a configuration 

message before attempting to reconfigure. All device ports (except for designated ports)  should 
receive  configuration  messages  at  regular  intervals.  Any  port  that  age  out  STA  information 
(provided in the last configuration message) becomes the designated port for the attached LAN. 
If  it  is  a  root  port,  a  new  root  port  is  selected  from  among  the  device  ports  attached  to  the 
network.

➤

 Fwd Delay: The  maximum  time (in  seconds)  the root  device  waits before  changing states (i.e., 

discarding  to  learning  to  forwarding).  This  delay  is  required  because  every  device  should 
receive information about topology changes before it starts to forward frames. In addition, each 
port  needs  time  to  listen  for  conflicting  information  that  would  make  it  return  to  a  discarding 
state; otherwise, temporary data loops might occur.

➤

 Topology: Indicates if  spanning tree topology is steady or undergoing reconfiguration. (The time 

required for reconfiguration is extremely short, so no values other that “steady” state are likely to 
be seen in this field.)

➤

 Root ID : The priority and MAC address of the device in the Spanning Tree that this switch has 

accepted as the root device, and the port connected to the root device. 

IGMP Status

IGMP Status

IGMP Status shows the IGMP Snooping statistics for the whole switch.

➤

 VLAN ID: VLAN ID number.

➤

 Querier: Show whether Querying is enabled.

➤

 Queries transmitted: Show the number of transmitted Query packets.

➤

 Queries received: Show the number of received Query packets.

➤

 v1 Reports: Show the number of received v1 Report packets.

➤

 v2 Reports: Show the number of received v2 Report packets.

➤

 v3 Reports: Show the number of received v2 Report packets.

➤

 v3 Leave: Show the number of v3 leave packets received.

Figure 2-5

VeriPHY

VeriPHY Cable Diagnostics

Wildix WSG08POE User Manual 

28

Summary of Contents for WSG08POE



































Reviews:

No comments