Wildix W01PRI Admin Manual Download

Page: 4 / 11

W01-02PRI Installation Admin Guide - English

Page 4 of 11

Green

100 Mbps

Yellow

1000 Mbps

Switches

Switch

Description

Reset/Default

Allows setting the device to default (known) values. Refer to

Reset of the Gateway

Connectors and ports

Connectors

/ports

Description

SYNC IN

8 KHz TDM synchronisation pulse input

SYNC OUT

8 KHz TDM synchronisation pulse output

PRI port

RJ-45 connector for ISDN-PRI connectivity

ETH1

A 10/100/1000 BaseT Ethernet RJ-45 connector for access to a LAN, WAN or computer.

This port is by default used for uplink / WAN connection

ETH2-ETH3-

ETH4/ETH5

10/100/1000 BaseT Ethernet RJ-45 connector for access to a LAN, WAN or computer.

These ports are used by default for LAN connections

Rear panel

Description

POWER connector

Power switch

Grounding screw

Installation of W01/02PRI

Install the device on a flat surface or in an equipment rack

Connect the Telephony Interface Cables. Refer to

this Chapter

Connect the Ethernet Cables. Refer to one if these Chapters:

Using W01/02PRI on the Edge

Connecting W01/02PRI using DHCP Server

Summary of Contents for W01PRI












Search results

Summary of Contents for W01PRI

Reviews:

Related manuals for W01PRI

Brands by name

Popular brands

Wildix W01PRI, Admin Manual

Search results

Summary of Contents for W01PRI

Reviews:

Related manuals for W01PRI

Brands by name

Popular brands