Wildix W01PRI Admin Manual Download Page 9

Page: 9 / 11

W01-02PRI Installation Admin Guide - English

Page 9 of 11

set the IP address to 192.168.0.1 and the Network Mask to 255.255.255.0

set the IPv6 link-local address on all network links. The IPv6 link-local address can be found

underneath the unit

A partial reset will also modify the following parameters to their default value:

Service

Parameter

Default Value

AAA

Users.Password

User(s) from profile are restored with their factory password. All other

usernames keep their password.

Users.AccessRights

User(s) from profile are restored with their factory rights.

ServicesAaaType

(table)

Each service will be configured to use Local authentication and no

accounting mechanism.

CLI

EnableTelnet

Disable

TelnetPort

EnableSsh

Enable

SshPort

HOC

ManagementInterface

Lan1

SNMP

EnableSnmpV1

Disable

EnableSnmpV2

Disable

EnableSnmpV3

Enable

Port

161

Web

ServerPort

HTTPMode

Both

SecureServerPort

443

To perform Partial reset:

When the Power LED is steady or blinking rapidly, insert a small unbent paper clip into the Reset/Default

switch located at the front of the device

Note: It is not recommended to access the device on a regular basis through the Rescue Network

Interface.

Note: The Power LED will start blinking.

Summary of Contents for W01PRI












Search results

Summary of Contents for W01PRI

Reviews:

Related manuals for W01PRI

Brands by name

Popular brands

Wildix W01PRI, Admin Manual

Search results

Summary of Contents for W01PRI

Reviews:

Related manuals for W01PRI

Brands by name

Popular brands