manualshive.com logo in svg

Wildix W-AIR 3.80.x, Administrator'S Manual

Share
Download
Wildix W-AIR 3.80.x Administrator'S Manual Download Page 17

Alarm Type

: The type of event that triggers an alarm. The options are: Disabled, Man Down, 

No Movement, Running, Pull Cord, Emergency Button. 

Alarm Signal

: Call. The alarm is made as an outgoing call to the emergency number 

preconfigured for the extension. 

Stop Alarm from Handset

: Enable/Disable. The possibility to cancel an alarm from the 

handset. 

Trigger Delay

: The timeout of pre-alarm warning. If set to 0, the alarm is sent immediately 

(max. value is 255 sec.).  

Note: For Man Down alarm, add the default delay of 6 seconds which is the time needed for the alarm 
detection (e.g. if set to “0”, alarm is triggered after 6 sec, if set to “30”, alarm is triggered after 36 sec.) 

Stop Pre-Alarm from Handset

: Enable/Disable the possibility to cancel the pre-alarm from the 

handset. 

Pre-Alarm Delay

: The timeout during which the pre-alarm warning is displayed until the 

actual alarm is sent (max. value is 255 sec.) 

Howling

: Enable/Disable the howling of the handset when the alarm is triggered. 

After you have defined the Emergency profiles, click “Save” to apply. 

7.4. Assign emergency profile to handsets 

W-AIR Base Station (Multicell) 

1. Go to the menu “Extensions” 

Wildix W-AIR System - Administrator’s Manual 3.80.x 

 17

Summary of Contents for W-AIR 3.80.x




















Reviews:

No comments

Brands by name

Popular brands

Load more brands