11
Check and Adjustment of Valve Clearance
• Excessive valve clearance will cause noise and engine damage. Little or no
clearance will prevent the valve from closing and will cause damage to the valve
and the bike will have a loss of power. Check the valve clearance when the
engine is cold.
• Remove the center hole cap from the case cover, generator cover and cylinder
head cover.
• By using a T spanner or kick starer, rotate the generator flywheel
counterclockwise until the T mark on the flywheel lines up with the index mark
on the view hole. In this case, the piston may either be on the compression or
exhaust stroke. The adjustment must made when the piston is at the TDC (top
dead center) of the compression stroke, and both the intake and exhaust valves
are closed.
• This condition can be determined by moving the rocker arms. If they are free, it
is an indication that the valves are closed and that the piston is on the
compression stroke. If they are tight and the valves are open, rotate
the flywheel by 360 degrees and realign the T mark to the index mark.
• Check the clearance of both valves by inserting a feeler gauge between the
adjuster screw and the valve stem.
• The intake valve clearance should be .002 inches and exhaust valve clearance
should be .0024 inches.
• If it is necessary to make an adjustment, loosen the lock nut and turn the
adjusting screw so there is a slight resistance when the feeler gauge is
inserted. After completing the adjustment, tighten the lock nut while holding the
adjusting screw to prevent it from turning. Finally, recheck the clearance to
make sure that the adjustment was not disturbed.
• Reinstall all of the parts to their original positions.
Storage Procedure
• During extended storage, store in a well ventilated area. Empty the fuel tank
and start the engine to clear out the remaining fuel.
Battery
• This scooter uses a sealed lead acid battery, it is unnecessary to check or add
liquid ever. How ever you must charge with a 2 Amp trickle charger for 6-7
hours before using and at least once a month when in storage.
NOTE:
Never open the electrolyte of a sealed battery. Remove the battery from
the scooter and store separately in a well ventilated area when the scooter is not
in operation for long periods of time.
Spark Plug
NGK C7HSA
Gap .035
Engine Break-In
• Change it to 5W50, 10W50 or 15W50 synthetic oil.This is the most important
time for the engine and the life of your scooter, because your engine is brand
new, you should not carry excessive loads or ride at a high speed for a
prolonged period of time. Vary your speed, do not operate at a continuous
speed. Check the oil before starting. Run your bike under 30 mph for 1 hour
and then change the oil.
Control Functions
Speedometer
• Speed is measured in mph.
Odometer
• The total riding distance is indicated.
Fuel gauge
• The gauge indicates how much fuel is in the
tank (the gauge does not work when the
ignition switch is off). The needle moves
from full "F" to empty "E" as your fuel
decreases. Fill the tank with a good
grade of 89-90 octane unleaded gasoline.
High Beam Indicator LIght
• The high beam light indicates when the high beam headlight is in use. We strongly
recommend you use your high beams in the day time.
NOTE:
Apply the low beam to avoid obstructing the view of other drivers.
Turn Signal Indication Light
• The turn signals indicate that you are turning a chosen direction, push the button in the
desired turning direction, it will return to the center, however you must push in to cancel.
Speedometer
Odometer
Turn Signal
Indication Light
High Beam
Indication Light
Fuel Gauge
Tachometer
Cellphone Ring
Indicator
Right and Left
Rearview Mirrors
and Turn Signals
Headlights
Windshield
Rear Storage
Trunk / Back Rest
Turn Signals
Brake and Taillight
Rear Left and Right
Turn Signals
4
