Wilderness Systems Helix PD Owner'S Manual Download Page 21

Wilderness Systems, 575 Mauldin Road, Suite 200, Greenville, SC 29607

19

To reengage the steering control (J) push the steering control (J) handle past the vertical neutral position, towards the bow, 
until you feel it reengage.

Tip:

 The rudder will lock in place in the position it is in when the steering control handle is disengaged, allowing for greater 

control of your kayak.

Tip:

 The steering control (J) handle is height adjustable. Loosen the screws on the back of the handle, adjust to your preferred 

height, and retighten screws.

11.5 Using the Stowage Strap

To help stow the Helix PD (E) when not in use or to stabilize unit in swells or surf launches use the stowage strap (C). Pivot 
the Helix PD (E) forward into the stowed position. Secure the stowage strap (C) over the Helix PD (E) and buckle the stowage 
straps (C) male and female buckles together. Tighten the strap stowage (C) by pulling on the strap end on the male buckle.

12. STORAGE AND CARE INSTRUCTIONS

12.1 General Care Advice

Materials were chosen with a high level of corrosion-resistance. All of the materials used in the Helix PD are, as with most 
leisure maritime products, classed as “seawater resistant”, not “seawater-proof”.

• 

After use you should always remove the Helix PD from the water.

• 

After operation wash all components in fresh water, especially after use in brackish or salt water.

12.2 Instructions for Rinsing the System

Perform a fresh water, low pressure rinse on the entire system after use in brackish or salt water. 

Tip:

 While you are rinsing your unit is a good time to thoroughly inspect the unit for damage.

Summary of Contents for Helix PD

























Reviews: