7/7/04 . 8.1 . ecn 6890 . rev B
11/4/03 . 16.0 . ecn 6208 . rev A
2/21/02 10 0 edr 3279 rev NC
Printed in U.S.A. 7/04 F-2075-S Rev b
WILBUR CURTIS CO., INC.
6913 Acco St., Montebello, CA 90640-5403 USA
Phone: 800/421-6150
Fax: 323-837-2410
Technical Service Phone: 800/995-0417 (M-F 5:30A - 4:00P PST) E-Mail: [email protected]
Web Site: www.wilburcurtis.com
WARRANTY
We hereby certify that the products manufactured by the Wilbur Curtis Company, Inc., are, to thebest of our knowledge, free from
all defects and faulty workmanship.
The following warranties and conditions are applicable:
•
90 Days for Labor and 1 Year Parts from Date of Purchase from Factory:
This warranty covers all electrical parts,
fittings and tubing.
•
40 Months or 40, 000 Pounds of Coffee on a set of Grinding Burrs. (ADS Grinders)
• 2 Years from Date of Purchase:
This warranty covers electronic control boards and leaking or pitting of a stainless steel
body of a Brewer or Urn.
•
90 Days from Date of Purchase:
On replacement parts that have been installed on out of warranty equipment
All in-warranty service calls must have prior authorization from the manufacturer. For an RMA (Return Merchandise Authorization)
number, call the Technical Service Department at 1-800-995-0417. The Wilbur Curtis Company will allow up to 100 miles, round
trip, per in-warranty service call.
CONDITIONS & EXCEPTIONS
The warranty covers original equipment at time of purchase only. The Wilbur Curtis Company, Inc., assumes no responsibility for
substitute replacement parts installed on Curtis equipment that have not been purchased from the Wilbur Curtis Company. Inc The
Wil-
bur Curtis Company will not accept any responsibility if the following conditions are not met. The warranty does not cover and is
void
under these circumstances:
1) Improper operation of equipment. The equipment must be used for its designed and intended purpose and
function.
2) Improper installation of equipment. This equipment must be installed by a professional, certified technician and
must comply with all local electrical, mechanical and plumbing codes.
3) Wilbur Curtis Company will not be responsible for the operation of equipment at other than the stated voltages
on the serial plate.
4) Abuse or neglect (including failure to periodically clean or remove lime accumulations). Manufacturer is not
responsible for variation in equipment operation due to excessive lime or local water conditions.
5) Replacement of items subject to normal use and wear. This shall include, but is not limited to, light bulbs, shear
disks, “0” rings, gaskets, canister assemblies. whipper chambers and plates, mixing bowls, agitation assemblies
and whipper propellers.
6) Any faults resulting from inadequate water supply. This includes, but is not limited to, excessive or low water
pressure, and inadequate or fluctuating water flow rate.
7) All repairs and/or replacements are subject to our decision that the workmanship or parts were faulty and the
defects showed up under normal use.
8) All labor shall be performed during regular working hours. Overtime charges are the responsibility of the owner.
9) Charges incurred by delays, waiting time, or operating restrictions that hinder the service technician’s ability to
perform service is the responsibility of the owner of the equipment. This includes institutional and correctional
facilities.
10) All claims under this warranty must be submitted to the Wilbur Curtis Company Technical Service Department
before return of the unit to the factory.
11) All equipment returned to us must be repackaged properly in the original carton. No units will be accepted if
they are damaged in transit due to improper packaging.
12) Damaged in transit.
13) The resetting of safety thermostats and circuit breakers, programming and temperature adjustments are the
responsibility of the equipment owner.
NO UNITS OR PARTS WILL BE ACCEPTED WITHOUT A RETURN MERCHANDISE AUTHORIZATION (RMA). RMA NUMBER
MUST BE MARKED ON THE CARTON OR SHIPPING LABEL.
All in-warranty service calls must be performed by an authorized service center, where service is available. Call the factory for
location near you.
