manualshive.com logo in svg

WIKA IPT-2 Series, Operating Instructions Manual

Share
Download
WIKA IPT-2 Series Operating Instructions Manual Download Page 9

9

3 Product description

WIKA Operating Instructions - Process pressure transmitter IPT-2x

1

2

Fig. 2: Example, electronic differential pressure for level measurement in pres-

surized vessel
1 IPT-2x

2  IPT-2x, slave sensor

The sensors are connected via a screened four-wire cable. The 

measured value from the slave sensor is read in and factored into the 

calculations. Power supply and parameter adjustment are carried out 

through the master sensor.
Information:

The sensor versions "

Relative pressure climate-compensated

" as 

well as "

Double chamber housing

" are not suitable for connection of a 

slave sensor.
You can find further information in chapter "

Combination Master - 

Slave 

" of this operating instructions.

The process pressure acts on the sensor element via the process dia-

phragm. The process pressure causes a resistance change which is 

converted into a corresponding output signal and output as measured 

value.
Piezoresistive sensor element

Measuring ranges up to 40 bar: piezoresistive sensor element with 

internal transmission liquid is used.

Measuring system

Summary of Contents for IPT-2 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands