WIKA DPT-20 Operating Instructions Manual Download Page 11

Page: 11 / 88

3 Product description

WIKA Operating Instructions - Differential pressure transmitter DPT-20

3.4 Packaging, transport and storage

Your instrument was protected by packaging during transport. Its

capacity to handle normal loads during transport is assured by a test

based on ISO 4180.
The packaging consists of environment-friendly, recyclable card

board. For special versions, PE foam or PE foil is also used. Dispose

of the packaging material via specialised recycling companies.

Caution:

Instruments for oxygen applications are sealed in PE foil and provided

with a label "Oxygen! Use no Oil". Remove this foil just before mount-

ing the instrument! See instruction under "

Mounting

Transport must be carried out in due consideration of the notes on the

transport packaging. Nonobservance of these instructions can cause

damage to the device.

The delivery must be checked for completeness and possible transit

damage immediately at receipt. Ascertained transit damage or con-

cealed defects must be appropriately dealt with.

Up to the time of installation, the packages must be left closed and

stored according to the orientation and storage markings on the

outside.

Unless otherwise indicated, the packages must be stored only under

the following conditions:

•

Not in the open

•

Dry and dust free

•

Not exposed to corrosive media

•

Protected against solar radiation

•

Avoiding mechanical shock and vibration

•

Storage and transport temperature see chapter "

Supplement -

Technical data - Ambient conditions

•

Relative humidity 20 … 85 %

With instrument weights of more than 18 kg (39.68 lbs) suitable and

approved equipment must be used for lifting and carrying.

3.5 Accessories

The display and adjustment module is used for measured value indi

cation, adjustment and diagnosis.

DI-PT-E iis an external display and adjustment unit for sensors with

single chamber housing and Ex d double chamber housing.

The overvoltage arrester is used instead of the terminals in the single

or double chamber housing.

The suitable mounting accessories for DPT-20 include oval flange

adapters, valve blocks as well as mounting brackets.

Packaging

Transport

Transport inspection

Storage

Storage and transport

temperature

Lifting and carrying

Display and adjustment

module

External display and

adjustment unit

Overvoltage protection

Mounting accessories

Summary of Contents for DPT-20

























































































Search results

Summary of Contents for DPT-20

Reviews:

Related manuals for DPT-20

Brands by name

Popular brands

WIKA DPT-20, Operating Instructions Manual

Search results

Summary of Contents for DPT-20

Reviews:

Related manuals for DPT-20

Brands by name

Popular brands