Installation instructions (translation from original)
wienet
IoT-Gateway Starterkit
IOT SK 115-W
83.041.1000.0
Wieland Electric GmbH
Brennerstraße 10 – 14
96052 Bamberg
Phone +49 951 9324-0
Fax
+49 951 9324-198
Doc. #
BA001201
– 07/2019 (Rev. A)
wienet
IOT SK 115-W
EN
NOTE
Personnel which installs, programs, operates or maintains this device must have read and
understood these instructions.
WARNING
•
The personnel must be thoroughly familiar with all warnings, notes and procedures de-
scribed in these operating instructions.
•
Where necessary, safety precautions and safety devices must comply with the applicable
regulations.
•
Damaged products must neither be installed nor put into operation.
•
The unit must not be opened.
•
Do not insert any objects into the unit!
•
Keep away from fire and water!
1
Function description
The
wienet
IoT gateway communicates with the
wienet
Cloud via Ethernet and the existing
network infrastructure. The communication mechanism has a low data volume and can be
integrated easily in the existing network infrastructure.
The IoT gateway is designed for an installation on a grounded 35 mm DIN rail in dry rooms.
The power supply of the device must be a grounded circuit PELV (connection between func-
tional earth and ground). The power supply must be a limited power source according to
the EN60950-1 chap. 2.5 or must be provided with an anti-surge fuse of 2 A.
2
Functional elements and indicators
Pin assignments and connections
Power supply
FE
GND
VCC
Functional earth
Ground
24 VDC
Serial interface: RS485
Pin A
A (- / Y)
Pin B
B (+ / Z)
LEDs
Ethernet interface: ETH 0 and ETH 1
Green LED
Link indication
Yellow LED
Activity indication
Status LEDs
P
Device is powered
A
PLC status
B
Portal status
3
Installation
Mounting on support rail (see fig. 3)
1.
Tilt the unit slightly backwards.
2.
Fit the unit over top hat rail.
3.
Push the unit downwards and against the rail for locking.
4.
Check that the unit is locked into position.
Connecting to power
Prepare a suitable power source and connect to the
IoT gateway.
Connecting to network device via ethernet
Connect your device by standard UTP/STP cable with RJ45 connectors to the IoT gateway.
4
Access to the web interface for the IoT gateway
The IoT gateway
is configured via a web interface using a web browser. Open the following
URL in the browser and enter the login data:
Address: http://192.168.1.10
User name: admin
Password: wienet123
The web interface then opens. If the window does not open, please check the proxy settings
for the browser you are using. Please do not use a proxy!
5
Load factory settings (reset)
1.
Disconnect the IoT gateway from the power supply.
2.
Press the reset button with a pointed object (e.g. a paper clip) and keep it pressed (until
step 5).
3.
Connect the IoT gateway to the power supply.
4.
Wait until the IoT gateway confirms the reset by two short flashes of all LEDs.
5.
Release the reset button and wait until the IoT gateway finished the restart. Do not dis-
connect the device from the power supply during the restart.
6
Removal from DIN rail (fig. 4)
WARNING
Switch mains power off and disconnect your system from the supply network.
Push down the power supply, and tilt upwards.
7
Technical data
Power supply
Supply voltage
24 VDC (
±
15%)
Active current
<50 mA (without I/Os)
Interface
SD card interface (see fig. 2) microSD card
Connectors
Wiring
Screw terminal, 2-/3-pole
Connector cross-section
0.2…2.5 mm² (AWG 30 – AWG 12)
Stripping length
7 – 8mm
General data
Operating temperature
0…+55 °C
Storage temperature
-20…+60 °C
Dimensions
see dimensional drawing, fig. 1
Degree of protection
IP20
EMC emission
IEC 61000-6-3
EMC immunity
IEC 61000-6-2
Compliance
CE
8
Scope of supply
•
1 IoT Gateway GW 115-W
•
1 microSD card
•
1 installation instructions
•
1 Connector 3-pin
•
1 Connector 2-pin
•
1 Label MAC-ID
1
2
3
4
microSD
ETH1
ETH0
Reset
