Release variant 1
For freely accessible
latch mechanisms
Place the screwdriver
on the interlocking clip
(1), as for example bet-
ween the distribution
block P12 and the sup-
ply connector P6 or the
output connector P1
with the switching devi-
ce P20, and disengage
by lifting the latch
mechanism (2) while
simultaneously separa-
ting the plug-and-
socket connection (3).
gesis
EIB V-......
P 7
Supply: Mains
connection (socket), 5 pole (L1, L2, L3, N,
PE)
P 8
Supply:
Bus connection (socket), 2 pole (+, -)
P 9
Routing:
Mains / EIB combination connector (plug)
5 / 2 pole (L1, L2, L3, N, PE / +, -)
P 10
Routing:
Mains (plug), 5 pole (L1, L2, L3, N, PE)
P 11
Routing:
EIB (plug), 2 pole (+, -)
P 12
Routing:
EIB (plug), 2 pole (+, -)
P 13
Slot (12 x 5.5 mm) for fixing the switching device with a
countersunk screw. Recommended screws: 4.5 x 40 mm
countersunk screws when using 6 mm plastic plugs
P 14
Hinged clip for securing the plug-and-socket connection
P 15
Supply plug integrated into the switching device
Both the single-phase devices
gesis
EIB V-0/4 1PH
and the
three-phase devices
gesis
EIB V…
have a 5 pole mains
connection
P 16
LED for displaying the programming state
P 17
Push button for setting device to programming state
P 18
Labelling field for the physical address
P 19
Slot (7.5 x 5.5 mm) for fixing the switching device with a
countersunk screw. Recommended screws: 4.5 x 40 mm
countersunk screws when using 6 mm plastic plugs
P 20
Switching device
gesis
EIB….
P 21
Fixing possibilities on the switching device for leading the
extension cables via the switching device
P 22
Sockets integrated in the switching device for connecting
consumer loads. The number of poles and the terminals
are the same as for the output connectors P1
Assembly using
flat cable P4
1. Enter the physical address on labelling field P18.
2. The device should possibly be preprogrammed with a
programming layout consisting of a power supply and an
interface.
3. Attach the flat cable adapter P5 to the flat cable P4, while
observing the installation instructions for the flat cable
adapter.
4. Snap the locking device P3 into place in the flat cable adap-
ter P5.
5. Open the fixing clip P14 for the supply cable as indicated
below.
6. Latch the flat cable adapter tight into the appliance connec-
tor P15.
7. Fix the switching device in the required position using
countersunk screws via the slots P13 (12 x 5.5 mm) and P19
(7 x 5.5 mm). (drilling distance 230 mm x 64.5 mm)
8. Close the fixing clip P14 again since is not required for this
variant.
Assembly using
round cables
9. Enter the relevant physical address on the labelling field
P18.
10. The device may possibly need to be preprogrammed with
a programming layout consisting of a power supply and an
interface.
11. Open the fixing clip P14 for the supply cable as indicated
below.
12. When using P6 or P7 without a distribution block P12, snap
the interlocking clip P2 into place.
13. Latch the supply cable P6 or P7 and P8 or the distribution
block P12 into the switching device.
14. When using the distribution block P12, snap the supply
cables P6 or P7 and P8 into place in the distribution block.
15. Latch the fixing clip P14 again.
16. Snap any extension cables into place in the distribution
board P12.
17. Any cables for further connection beyond the switching
device can be fixed in P21 as shown.
Opening the fixing
clip P14
Pull the fixing clip out-
wards on the side
with the arrow (1), lift
slightly (2) and then
swivel by 90°. If it
needs to be removed
completely, it should
be pulled from the
opposite side (1) and
removed.
Release variant 2
For inaccessible latch
mechanisms
Place the screwdriver
(1) at the side between
the connector and the
relevant interlocking
clip, as for example bet-
ween the switching
device P20 and the
supply plug-and-socket
connections P5, P6, P7
or P12 and lift the lat-
ching device (2). The
connection is disenga-
ged by simultaneously
separating the connec-
tor (3).
Dismantling when using
flat cables P4
18. Remove the output connector P1 as indicated for release
variant 1.
19. Open the fixing clip P14 as indicated above.
20. Unscrew the switching device by loosening the counter-
sunk screws (P13 and P19).
21. Remove the flat cable adapter P5 from the switching device
as indicated for release variant 2.
22. If necessary, unscrew the flat cable adapter P5 from the flat
cable, while taking into account the installation instructions.
23. If a flat cable adapter is no longer to be attached, the
piercing holes should be sealed with a few twists of insu-
lating tape.
I m p o r t a n t n o t e
Assembly of switching devices
❚
Connectors must audibly latch into place when
they are plugged in
❚
All cables must be fixed and supplied with a suffi-
cient strain relief
❚
The devices must be protected against damp, dirt
and from being damaged
❚
The devices may not be operated outside the spe-
cific technical data
❚
The appropriate standards, guidelines, regulations
and conditions for setting up electrical installations
should be complied with as well as the relevant
safety specifications
C a u t i o n
Before assembling the flat cable adap-
ter P5, ensure that the flat cable P4 is
de-energized.
g
C a u t i o n
Before dismantling the flat cable
adapter P5, ensure that the flat cable
P4 is de-energized.
g
1
2
3
1
2
3
3
2
1
