background image

Assembly

Stage J.

21). Fit 1 x Pulley (68) And 2 x Pulley Bearing so the Floa�ng Pulley Bracket (17) (Inset "E"), using 1 x M10 x 40mm Hex Bolt (26),  

2 x M10 Flat Washers (38) and 1 x M10 Nylon Locknut (35).

22). Fit the remaining Pulley (68) to the Auxiliary  Leg Pulley Br

a

cket (17A) (Inset "F"), using 1 x M10 x 40mm Hex Bolt (26), 

2 x M10 Flat Washers (38) and 1 x M10 Nylon Locknut (35).

 

Fit this assembly to the Front Upright near the Backrest Frame - Front

Upright fixing bracket using, 2 x M10 Flat Washers (38) and 1 

x

 M10 Nylon Locknut (35).

Note: - The Auxilia

r

y Leg 

P

ulley Bracket should be able to 

r

otate when assembled.

23). Connect one end of the Leg Extension Cable (49) to the bracket on the back of the Leg Extension 

(Inset "G"), Ioca�ng the 

Leg Cable Pin (44) in the posi�on. F

i

t a Carabina Clip to the other end of this Cable.

24). Take the THREADED end of the Weight Stack Cable (47) and pass it through the Auxiliary Leg Pulley Bracket fi�ed in Stage 

J-22 above. Route this cable up the Front Upright and around the Pulleys shown in lnset "H" following the route in lnset

"I", over the rearmost Pulley and down into the Selecto

r S

ha�, securing in place by first fi�ng the M12 Top Plate Washer (37) then 

�ghtening the threaded end of the cable securely in the Selector Sha�.

25). Take the LOOPED end of the Lat Cable (48) and pass it through the Top Lat Bar Bracket; Over the Top Front Lat Pulley; 

Around the Top Rear Pulley; Down the rear of the Front Upright; Under the Lower Cross Beam Pulley; Over the Chest Press Bar

Pulley; Under the Rear Upright Lower Pulley then connect the Carabina clip(45) And Chain (72) to the Lat Cable end with 1 x M8 x 25mm  

Hex Bolt (73) and 1 x M8 Nylon Locknut (74) & 2 x Washer (39). Fit the Adjuster Chain(72), using the link that reduces overall cable slack

and hook onto the Floa�ng Pulley Bracket (17). 

O

nce this cable is secure, fit the Let Ber (15) to the Carabina Cllp lay in

posi�on on the rest hooks by the Front Lat Pulley.

Note: - T

o fu

r

ther reduce or increase cable slack in your system you can make fine adjustments by screwing fu

r

ther in (to reduce 

slack) or unscrewing (to increase slack) the Thread

ed F

itment on the Weight Stack Cable. Please ensure that at least 30% of the 

thread on this cable end is screwed into the Selector Sha�.

47

47

26

38 69

69 35

17A

38

47

47

49

15

35

26

17

73

45

48

72

47

74

47

37

48

45

48

P

age 

23

Summary of Contents for HGYM





























Reviews: