background image

5   |   P a g e

   

 

 

ZBOOST® YX500/510 SERIES USER GUIDE

 

Warning

 

 

The zBoost® YX500/510 Series base unit MUST only be used 
with the provided power adaptor. Use of other power adaptors 
will void the warranty and may damage the unit. Use of other 
equipment is not FCC approved.

 

 

Additional Cable Requirements 

If the distance between the Signal Antenna and the Base Unit exceeds 35 feet  (YX500-PCS) or 
50 feet (YX500-CEL or YX510-Dual Band), you will need to purchase additional coaxial cable for 
a total coax cable length of 70 feet. You may use RG-6 coaxial cable and F connectors, which 
are rated for outdoor satellite TV use and can be found at many home improvement and 
electronic stores. 

For the best performance, purchase RG-6 low-loss extension cables from our website or your 
retailer. The total cable length should not exceed 70 feet unless you also purchase an 
upgraded signal antenna (

see page viii

). A longer cable is helpful only if it allows you to place 

the Signal Antenna in a location where you measure stronger signal.

 

Grounding the Signal Antenna

 

If you decide to place the Signal Antenna outdoors, it must be properly grounded.  

The set up must be in accordance with Article 810 of the National Electric Code (NEC). A listed 
antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 
or the shield of the coaxial cable must be permanently and effectively grounded in 
accordance with NEC article 8.10.21. Please consult a professional installer or electrician for 
more information. Additional instructions and hardware are also available in the zBoost® 
Outdoor Grounding Kit (

see page viii

).

 

Securing Cable with a Drip Loop

 

FIGURE 5: Securing 

Cable with a Drip Loop

If you place the Signal Antenna outdoors, create a drip loop with 
the coaxial cable at the point where the cable enters the building 
through an outside wall. This can be done by twisting and securing 
the cable into a loop (no less than 4” across) near the entry point. 
This will help prevent moisture from gathering at entry point and 
leaking into the building. Consult a professional installer if you 
need more information. Additional instructions are also available 
in the zBoost® Outdoor Grounding Kit (

see page viii). 

 

 

 

Power Requirements

 

The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the 
Included power supply. The power supply consumes less than 10W (less than 0.2A). 

 
 
 
 
 
 
 
 

 

Coax

Cable

Exterior Wall

P a g e   |   6  

 

ZBOOST® YX500/510 SERIES USER GUIDE

Setting Up Your zBoost® Signal Booster 

 

 

 

 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

 
 
 

FIGURE 6: Placing the Signal Antenna Inside, Near a Window 

Placement of the Signal Antenna

 

Choosing the best location for the Signal Antenna provides the best performance and the 
largest area of improved signal. Determine the location that provides the strongest signal using 
the signal strength indicator on your cell phone. Find the location that provides the most bars 
of signal strength and place the Signal Antenna at or near that location.

 

Avoid placing the Signal 

Antenna near metal such as wiring, A/C ducts, metal siding, truss plates, etc. When connecting 
the cable to the antenna, run the cable straight down from the antenna. Avoid draping the coax 
near the antenna. 

Choose 1 of the following 3 options for setting up your zBoost® system:

 

EASIEST:   

Inside, by a window

 

 

1.

 

Locate a window where you get signal.   

2.

 

Mount the Signal Antenna above the window. 

3.

 

Place the Base Unit in desired location – where you 
want to create a Cell Zone™ (15 feet of vertical 
separation between the Base Unit and Signal 
Antenna is recommended). 

4.

 

Attach the coaxial cable to the Signal Antenna. 

5.

 

Connect the other end of the coaxial cable to the 
Base Unit. 

6.

 

Attach the Base Unit Antenna to the Base Unit and 
position it vertically. 

 

7.

 

Connect the Power Supply to the Base Unit and plug into a power outlet.

 

NOTE

:  If a red light appears, try further separating the Signal Antenna and Base Unit or see the 

Troubleshooting section (Page 12). 

 

Easiest Set-Up:  

Place the Signal Antenna 
inside, by a window

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 

 

B

B

a

a

s

s

e

e

 

U

U

n

n

i

i

t

t

 

 

S

S

i

i

g

g

n

n

a

a

l

l

 

A

A

n

n

t

t

e

e

n

n

n

n

a

a

 

 

C

C

o

o

a

a

x

x

 

C

C

a

a

b

b

l

l

e

e

 

 

P

P

o

o

w

w

e

e

r

r

 

S

S

u

u

p

p

p

p

l

l

y

y

 

 

Summary of Contents for zBoost YX500 SERIES















Reviews: