background image

 

OPERATION INSTRUCTIONS 

IMPORTANT: 

Do not plug in the refrigerator for 24 hours after unit is set in place. Failure to do so may 

result in the unit working improperly. 

This refrigerator has a rotary temperature control knob (thermostat) inside the unit which is marked with 
the settings 

OFF-COLD-COLDEST

 in order of increasing coldness. In addition, this model employs a 

heater inside the cabinet and is designed for outdoor use.  

Note:

 To prevent excessive strain on the compressor, do not leave the unit at the 

COLDEST

 setting for 

more than an hour at a time. 

 
Turning on the Unit 

The refrigerator turns on automatically when it is plugged in. When the air temperature is below 

40°F, follow this procedure to stop the compressor: 

1.  Turn the temperature control knob (thermostat) to the 

COLD 

setting. 

2.  Continuing turning the control knob counter-clockwise to the

 OFF

 setting. The compressor will stop 

working and the heater will turn on automatically to maintain the temperature at a suitable level.  
 

 

If the ambient temperature is above 40ºF, turn the thermostat to the range between 

COLD

 and 

COLDEST

 to cool foods. 

 

If the ambient temperature is below 30°F, do not use the unit to store anything. 

 

If you unplug the refrigerator or the power is cut off accidentally, allow 8 minutes before 
restarting it or plugging it back in. It will not operate properly in less than 8 minutes. 
 

Temperature Setting 

Initially set the thermostat to the midpoint between the 

COLD

 and

 COLDEST

 settings. The 

compressor will run continuously for a few hours until the temperature inside the appliance becomes 
stable. After this, the compressor runs normally (i.e., turns on and off periodically). 

When the unit is operated for the first time, it is suggested that you not put food inside until the 

compressor is running normally. 

Adjusting the thermostat clockwise will make the compressor run for a longer time with a shorter 

compressor stop time, and the temperature inside the appliance will become colder. The setting should 
be regulated according to ambient conditions and the desired temperature. The compressor will run for 
a while after each regulation before reaching a steady temperature. 

Note: 

Cold air falls and warmer air rises, and there will be a small temperature variation from the bottom 

of the unit to the top. The temperature at the bottom of the unit will always be slightly colder. 

 

Operating the Internal Light 

This appliance has an internal light to make it easier for you to see the foods you have stored. 

When the door is open, the light will be on and when it is closed, the light will be off. 

 
Shelving 

The wire racks in your refrigerator are chrome-plated so they will not rust. The unit has 3 

adjustable chrome-plated flat wire shelves and a wire basket to hold cans and bottles of beverages 
such as beer, water and soft drinks.  These racks are removable and reversible. To take out a rack, 
remove any cans or bottles from the rack and pull it out until it stops. Then lift up the front of the rack and 
remove it from the unit. 

 
Normal Sounds 

Your new refrigerator may make sounds that are not familiar to you. Hard surfaces like the floor, 

walls can make the sounds seem louder than they actually are. The following describes the kinds of 
sounds that might be new to you and what may be making them. 

 

Ratting noises may come from the flow of the refrigerant or the water line, items stored on top of 
the refrigerator can also make noises.  

 

The high efficiency compressor may make a pulsating or high-pitched sound. 

 

Water running from the evaporator to the water bin may make a splashing sound. 

 

You may hear air being forced over the condenser by the condenser fan. 

Summary of Contents for BOR-325FS













Reviews: