White Outdoor 100 Series Operator'S Manual Download Page 9

4

Operating 

Your Lawn 

Mower

WARNING

The operation of any 

lawn mower can result 

in foreign objects 

being thrown into 

the eyes, which can 

damage your eyes 

severely. Always wear 

safety glasses while 

operating the mower, 

or while performing 

any adjustments or 

repairs on it.

Be sure no one other 

than the operator is 

standing near the lawn 

mower while starting 

engine or operating 

mower. Never run 

engine indoors or 

in enclosed, poorly 

ventilated areas. En-

gine exhaust contains 

carbon monoxide, an 

odorless and deadly 

gas. Keep hands, feet, 

hair and loose clothing 

away from any moving 

parts on engine and 

lawn mower. 

Figure 

3. Standing behind the mower, squeeze the 

blade control against upper handle, Figure 

9. The choke will now begin to slowly return 

to the off choke position after activating the 

blade control. Therefore, quickly move onto 

step four below. 

4. Grasp the starter handle as shown and pull 

slowly until resistance is felt, then pull rapidly 

to start engine and avoid kickback. Return it 

slowly to the rope guide.

WARNING: Wait for the blade to 

stop completely before perform-

ing any work on the mower or to 

remove the grass catcher.

To Stop Engine :
1.  Release the blade control handle to stop the 

engine and blade. 

WARNING: The blade continues 

to rotate for a few seconds after 

the engine is shut off.

2. Disconnect and ground the spark plug wire 

as instructed in the separate engine manual 

to prevent accidental starting while equip-

ment is unattended.

Using Your Lawn Mower

Be sure the lawn is clear of stones, sticks, wire, 

or other objects which could damage the lawn 

mower or the engine. Such objects could be 

accidently thrown by the mower in any direction 

and cause serious personal injury to the opera-

tor and others.

WARNING: If you strike a foreign 

object, stop the engine. Remove 

wire from the spark plug, thor-

oughly inspect the mower for any 

damage, and repair the damage 

before restarting and operating 

the mower. Extensive vibration 

of the mower during operation is 

an indication of damage. The unit 

should be promptly inspected 

and repaired.

Operating Tips
1.  For best results and effective mulching, do 

not cut wet grass.

2. New grass, thick grass, or wet grass may 

require a narrower cut.

3. For a healthier lawn, never cut off more than 

one-third of the total length of the grass. 

4. Your lawn should be cut in the fall as long as 

there  

is growth.

5. Adjust ground speed according to condition 

of lawn.

6. If the grass has been allowed to grow in 

excess of 4 inches, mulching is not recom-

mended. Mow using the side discharge to 

reduce the grass height to 3-1/4 inches or 

less before mulching.

ON

OFF

2

3

4

1

Summary of Contents for 100 Series





























Reviews: