manualshive.com logo in svg

Whisper 1400 EP, Operation Manual

Share
Download
Whisper 1400 EP Operation Manual Download Page 6

6

the tail into position.  Use 5 min. epoxy to glue the stabilizer 

in place.  It is important to keep the stabilizer level in 

regards to the fuselage and the fin perpendicular to the 

stabilizer while the glue cures.  Also, make sure the eleva-

tor pushrod had stayed inserted into its connector on the 

elevator servo horn.

Level with fuselage

4.

  IMPORTANT:  Before flying, you must turn the 

radio on (with receiver battery charged and transmitter 

batteries installed) and check that the elevator and rud-

der are in the neutral position with the transmitter 

stick and trims in neutral.  Securely tighten the hex 

screw on the elevator pushrod connector on the eleva-

tor servo horn.  Also, adjust the rudder pushrod if 

needed.

Black

Negative

Red

Positive

1.  Hookup as shown
2. 

Turn charger knob to 30

3. Make sure LED lights

4. Wait until charger clicks off (30 min.)

CAUTION:

•      Maintain Polarity; 

      Red to + (positive)

      Black to – (negative)

•      Do not leave the battery 

      unattended while charging

•      If battery pack gets hot, 

      disconnect and use

Knob

LED

12 Volt Battery

MAINTAIN 

POLARITY!

Figure 2.    Charge the Batteries

Summary of Contents for 1400 EP













Reviews:

No comments

Brands by name

Popular brands

Load more brands