3
Electrical Requirements
Observe all governing codes and ordinances.
Required:
■
A 120-volt, 60 Hz, AC-only, 15- or 20-amp electrical supply
with a fuse or circuit breaker.
Recommended:
■
A time-delay fuse or time-delay circuit breaker.
■
A separate circuit serving only this microwave oven.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■
For all cord connected appliances:
The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed
and grounded.
WARNING:
Improper use of the grounding plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven.
This device complies with Part 18 of the FCC Rules.
This device complies with Industry Canada ICES-001.
OPERATING YOUR MICROWAVE OVEN
IMPORTANT:
If there are two packing spacers on top of the vent grille, remove them before using the microwave oven.
Settings
Clock
The Clock is a 12-hour (12:00-11:59) or 24-hour (0:00-23:59)
clock. Touch OPTIONS/CLOCK to reach Clock submenu, and
follow the prompts to set the Clock. Clock format (12 hours with
AM and PM, 12 hours without AM and PM or 24 hours) may also
be set in the Clock submenu.
Timer
With the microwave oven in Standby mode, touch the Timer
keypad, enter time, then touch the Timer keypad or the Start
keypad. Cook functions may be entered while the timer is
counting down. To cancel timer, touch Timer keypad while the
Timer countdown is active in the display.
Control Lock
Activate to avoid unintended start. Touch and hold the Cancel
keypad for about 3 seconds until 2 tones sound and Padlock icon
appears in the display. Repeat to unlock control.
Options/Clock
Twelve options/settings may be adjusted: 1-Clock; 2-Scrolling
peed; 3-Sound; 4-Language (English or French); 5-Energy Save;
6-Auto Adapt Fan; 7-Filter Alert; 8-30 Minute Fan Timer; 9-Light
Timer; 10-Temp Calibration (on convection models); 11-Demo
Mode; 12-Factory Reset.
Vent Fan
Various speeds, ranging from high to low, and off. Comes on
automatically as cooling fan during any cook function.
30-Minute Fan Timer:
Set vent fan to run for exactly 30 minutes
or to run for only 30 minutes more (off after 30 minutes). The vent
fan may be turned off at any time using the Vent Fan control.
Touch OPTIONS/CLOCK to reach the 30-Minute Fan Timer
submenu and select the setting.
Auto Vent Fan (on some models):
To keep the microwave oven
from overheating, the auto vent fan will automatically turn on at
high speed if the temperature from the range or cooktop below
the microwave oven gets too hot. When this occurs, the vent fan
cannot be turned off. “AUTO FAN ON for heat circulation” appears
in the display.
Dynamic Fan Sensing (on some models):
To keep the
microwave oven from overheating, the auto vent fan will
automatically turn on at various speeds, depending on the
temperature from the range or cooktop below the microwave
oven. When this occurs, the vent fan cannot be turned off.
“AUTO FAN Sensor Technology for heat circulation” appears in
the display. As the temperature cools, the fan will automatically
decrease its speed, then turn off.
Light Timer
Set the cooktop light to turn on and off at certain times. Touch
OPTIONS/CLOCK to reach the Light Timer submenu and follow
the prompts to set the light on time and light off time in hours and
minutes, or to cancel Light Timer.
NOTE:
Light Timer uses 12-hour clock only.
Filter Alert
Reset the filter status after replacing and/or cleaning the filters.
Touch OPTIONS/CLOCK to reach the Filter Alert submenu and
activate reset.
Sound (Tones)
Programming tones and signals. Programming tones may be turned
off, or all tones (including end-of-function signals) may be turned off.
Touch OPTIONS/CLOCK to reach the Sound submenu, then follow
the prompts to turn off or on the programming tones or all tones.
Scroll Speed
Scroll speed of the text may be adjusted. Touch OPTIONS/
CLOCK to reach the Scroll Speed submenu and follow the
prompts to set speed.