background image

ICE MAKER INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION 

DE LA MACHINE À GLAÇONS

INSTRUCCIONES DE INSTALACIÓN 

DE LA FÁBRICA DE HIELO

W11255279B

TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE

ICE MAKER SAFETY

ICE MAKER SAFETY .................................. 1
INSTALLATION INSTRUCTIONS ............... 2

Unpack the Ice Maker .............................. 2
Location Requirements ............................ 2
Electrical Requirements ........................... 3
Water Supply Requirements .................... 4
Vacation or Extended Time Without Use .. 4
Connect Water Supply ............................. 4
Drain Pump Installation  

(on some models) ..................................... 5
Drain Connection ..................................... 8
Door Reversal—Side Swing Only ............ 9
Leveling .................................................. 11
Cleaning ................................................. 11

SÉCURITÉ DE LA MACHINE  

À GLAÇONS .............................................. 13
INSTRUCTIONS D’INSTALLATION ......... 14

Déballage de la machine à glaçons ....... 14
Exigences d’emplacement ..................... 14
Spécifications électriques ...................... 15
Spécifications de l’alimentation en eau .. 16
Vacances ou longue  

période d’inutilisation ............................. 16
Raccordement à la canalisation d’eau .. 16
Installation de la pompe de vidange 

(sur certains modèles) ............................ 17
Raccord au drain .................................... 20
Inversion du sens de la porte –  

porte à ouverture latérale uniquement ... 21
Mise à niveau ......................................... 23
Nettoyage ............................................... 23

SEGURIDAD DE LA FÁBRICA  

DE HIELO .................................................. 25
INSTRUCCIONES DE INSTALACIÓN ..... 26

Cómo desempacar la máquina  

de hielo ................................................... 26
Requisitos de ubicación ......................... 26
Requisitos eléctricos .............................. 27
Requisitos del suministro de agua ......... 28
Vacaciones o tiempo prolongado  

sin uso .................................................... 28
Conexión del suministro de agua .......... 28
Instalación de la bomba de desagüe  

(en algunos modelos) ............................. 29
Conexión de desagüe ............................ 32
Reversión de puertas— 

Solo lado de apertura ............................. 33
Nivelación ............................................... 35
Limpieza ................................................. 35

You can be killed or seriously injured if you don't immediately 
 

You

 

can be killed or seriously injured if you don't follow 

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety 
messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Summary of Contents for WUI75X15













Reviews: