Whirlpool WHESFC Installation And Operation Manual Download Page 16

Page: 16 / 26

. Press the

UP or

DOWN buttons to set ON or

OFF.

. Press the PROGRAM button four times to return to

the normal run display.

CLEAN FEATURE MINUTES

The Clean / Clear Water Iron Reduction feature

(described above) may be adjusted, from 1 to 15 min-

utes in length. To change this cycle time, use the UP

button to increase the time, or the DOWN button to

shorten the time. The default value for this feature is

2 minutes.

. Press and hold the PROGRAM button until the

screen in Figure 24 is displayed. Once in this dis-

play, press the PROGRAM button three times and

the display in Figure 27 is shown.

FIG. 27

Efficiency Icon

In the state of California: You must turn the Salt

Efficiency Feature ON. This may initiate more

frequent recharges. However, it will operate at

4,000 grains per pound of salt or higher.

Customizing Features / Options

SALT EFFICIENCY

When this feature is ON, the water conditioner will

operate at salt efficiencies of 4000 grains of hardness

per pound of salt or higher (May recharge more often

using smaller salt dosage and less water). The con-

ditioner is shipped with this feature set OFF.

. Press and hold the PROGRAM button until the

screen in Figure 24 is displayed. Once in this dis-

play, press the PROGRAM button once and one of

the two displays in Figure 25 is shown.

. Press the

UP or

DOWN buttons to set ON or

OFF. When set to ON, the efficiency icon will be

displayed in the lower left hand corner of the nor-

mal run display.

FIG. 24

FIG. 25

. Press the PROGRAM button five times to return to

the normal run display.

This feature is beneficial on water supplies containing

ferrous (clear water) iron. The default setting is OFF.

When this feature is set to ON, an additional back-

wash and fast rinse cycle will occur first, preceding

the normal regeneration sequence. This provides

extra cleaning of the resin bed before it is regenerat-

ed with the salt brine. To conserve water set this fea-

ture OFF if your water supply does not contain iron or

sediments.

. Press and hold the PROGRAM button until the

screen in Figure 24 is displayed. Once in this dis-

play, press the PROGRAM button twice and one of

the two displays in Figure 26 is shown.

CLEAN / CLEAR WATER IRON REDUCTION

FIG. 26

. Press the

UP or

DOWN buttons to set the

number of minutes.

. Press the PROGRAM button three times to return

to the normal run display.

Summary of Contents for WHESFC



























Search results

Summary of Contents for WHESFC

Reviews:

Related manuals for WHESFC

Brands by name

Popular brands

Whirlpool WHESFC, Installation And Operation Manual

Search results

Summary of Contents for WHESFC

Reviews:

Related manuals for WHESFC

Brands by name

Popular brands