background image

11

B

2.

 

Remove center screw

Remove center terminal block screw (B).

Connect remaining wires

4.

Place hooked ends of remaining direct wire cable wires  

under outer terminal block screws (hooks facing right).  

Squeeze hooked ends together and tighten screws. Finally, 

reinsert tab of terminal block cover into slot of dryer rear  

panel. Secure cover with hold-down screw. Now, go to Venting 

Requirements. 

B

C

Place hooked end of neutral wire (white or  

center) (C) of direct wire cable under center terminal block 

screw (B). Squeeze hooked end together. Tighten screw.

3.

 

Connect neutral wire

1.

 

Prepare to connect neutral 

     ground wire and neutral wire

A

E

B

Remove center terminal block screw (B). Remove neutral ground 

wire (E) from external ground conductor screw (A).

E

B

C

Connect neutral ground wire (E) and neutral wire (white or 

center wire) (C) of power supply cord or cable under center 

terminal block screw (B). Tighten screw.

Connect remaining wires

3.

Place hooked ends of remaining wires under outer terminal 

block screws (hooks facing right). Tighten screws. 

Optional 3-wire Connection

IMPORTANT:

 

You must verify with a qualified  electrician that 

this grounding method is acceptable before connecting.

2.

 

Connect neutral ground wire 

  and neutral wire

Summary of Contents for WED5500BW





















Reviews: