background image

22

Secure dishwasher to countertop

Locate brackets on top of dishwasher and secure dishwasher to 
countertop with two, #10 x 

¹⁄₂

" Phillips-head screws (included). 

The dishwasher must be secured to keep it from shifting when 
door is opened.

Side mount dishwasher to cabinet

NOTE: If side mounting dishwasher to cabinet, you must drill pilot 
holes in cabinet to avoid splitting the wood. 
Locate brackets on side of dishwasher and secure dishwasher to 
cabinet with two, #10 x 

¹⁄₂

" Phillips-head screws (included). The 

dishwasher must be secured to keep it from shifting when door is 
opened. 

Check that top of door does not contact screws, brackets or 
countertop. If it does, adjust leveling legs.

Open door and check that space between dishwasher cabinet 
opening and tub is equal on both sides. If spacing is not equal, 
loosen bracket screws secured and shift tub. Tighten bracket 
screws.

If securing with a side attachment, check that sides of door do not 
rub against the screw heads. If they do, dishwasher must be re-
centered. When dishwasher is properly centered, replace plastic 
butttons.

Remove towel from dishwasher. Reinstall the lower dish rack.

Summary of Contents for WDF750SAYM


























Reviews: