Whirlpool WDF750SAYM Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 25

background image

12

Using two or more people, grasp sides of dishwasher door frame
and place dishwasher on its back.

Remove and discard the plastic rail cover on each side of the
dishwasher frame. To remove the plastic rail cover, push upward
and back to unsnap it from the dishwasher frame.

Using a flat-blade screwdriver, turn the plastic fasteners ¼ turn
counterclockwise to unlock them. Remove panel. Do not remove
tech sheet from access panel.

Using a

¹⁄₄

" hex head socket, nut driver or Torx

®

T20

®

screwdriver,

remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure screw
heads are facing to the left when tightening conduit nut. Strain
relief is provided with the power supply cord kit.

NOTE: If using Option B, proceed to “Determine Cabinet
Opening,” to continue with the installation of your dishwasher.

«
...
10
11
12
13
14
...
»

Summary of Contents for WDF750SAYM


























Reviews:

No comments

Related manuals for WDF750SAYM

Brand: NEFF Pages: 2

Monogram ZBD0700

Brand: GE Pages: 32

Profile PDW8680N

Brand: GE Pages: 48

Monogram ZBD5600

Brand: GE Pages: 24

Triton XL GSD6900 Series

Brand: GE Pages: 2

Brand: GE Pages: 16

Brand: GE Pages: 2

Brand: GE Pages: 20

Brand: Bush Pages: 36

Brand: Bradley Pages: 25

Brand: Atag Pages: 116

Brand: Benton Harbor Pages: 7

Brand: NewAir Pages: 24

Brand: GE Pages: 70

Brand: Splendide Pages: 2

Brand: Farberware Pages: 27

Brand: Fagor Pages: 115

Brand: Kuppersberg Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands