Whirlpool W10459122A Installation Instructions Manual Download Page 6

6

INSTALLATION INSTRUCTIONS 

Unpack Range

1.  Do not use oven door handle to lift or move the range. 

2. Remove shipping materials, tape and film from range. Keep 

cardboard bottom under range. Remove oven racks and 
parts package from inside oven. 

3. Take 4 cardboard corners from the carton. Stack one 

cardboard corner on top of another. Repeat with the other 
2 corners. Place them lengthwise on the floor behind the 
range to support the range when it is laid on its back. Using 
2 or more people, firmly grasp the range and gently lay it on 
its back on the cardboard corners. 

4. Pull cardboard bottom firmly to remove. 

5. Use a wrench or pliers to loosen the leveling legs. Adjust the 

leveling legs to the correct height. Leveling legs can be 
loosened to add up to a maximum of 1" (2.5 cm). A maximum 
of 

³⁄₁₆

" (5.0 mm) is needed to engage the anti-tip bracket.

 NOTE: If height adjustment is made when range is standing, 
tilt the range back to adjust the front legs, then tilt forward to 
adjust the rear legs. 

6. Place cardboard or hardboard in front of range. Using 2 or 

more people, stand range back up onto cardboard or 
hardboard.  

Install Anti-Tip Bracket

1. Remove the anti-tip bracket from where it is attached inside 

the oven with a wire tie.

2. Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor, you can use the wall 
mounting method. If you are installing the range in a mobile 
home, you must secure the range to the floor.

3. Determine and mark centerline of the cutout space. The 

mounting can be installed on either the left side or right side 
of the cutout. Position mounting bracket against the wall in 
the cutout so that the V-notch of the bracket is 7

⁷⁄₈

" (20 cm) 

from centerline as shown.

4. Drill two 

¹⁄₈

" (3 mm) holes that correspond to the bracket 

holes of the determined mounting method. See the following 
illustrations.

A. Cardboard shipping base 

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

A

A. 7

⁷⁄₈

" (20 cm)

B. Bracket V-notch

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation 
instructions.

Slide range back so rear range foot is engaged in the 
slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed 
and engaged.

Failure to follow these instructions can result in death 
or serious burns to children and adults.

Centerline

B

A

Summary of Contents for W10459122A













Reviews: