Whirlpool W10435039A Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 23

background image

12

Using 2 or more people, grasp sides of dishwasher door frame
and place dishwasher on its back.

Using a flat-blade screwdriver, turn the plastic fasteners

¹⁄₄

turn to

unlock them. Remove panel. Do not remove tech sheet from
access panel.

Using a

¹⁄₄

" hex head socket, nut driver or Torx

®

T20

®

screwdriver,

remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure screw
heads are facing to the left when tightening conduit nut. Strain
relief is provided with the power supply cord kit.

NOTE:

If using Option B, proceed to “Determine Cabinet

Opening,” to continue with the installation of your dishwasher.

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower
part of dishwasher tub. Pull cord through strain relief in terminal
box.

«
...
10
11
12
13
14
...
»

Summary of Contents for W10435039A
























Reviews:

No comments

Related manuals for W10435039A

Brand: NEFF Pages: 2

Brand: NEFF Pages: 2

Brand: NEFF Pages: 2

Brand: Fagor Pages: 112

NAGOLD SERENE FI02

Brand: Hafele Pages: 59

Brand: Smeg Pages: 44

Brand: Amica Pages: 2

Brand: ZANKER Pages: 4

Brand: Speed Queen Pages: 1

Brand: Smeg Pages: 12

Brand: Gaggenau Pages: 72

Brand: Heinner Pages: 85

Brand: Samsung Pages: 10

Brand: Samsung Pages: 132

Brand: Samsung Pages: 9

Brand: Samsung Pages: 10

Brand: Samsung Pages: 38

Brand: Samsung Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands